We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
nRF52832 power consumption is high after the SPI peripheral is used (approximately 400uA of extra current consumption). I expect it has something to do with the high speed...
Hi,
I am using the nrf52832 board for my project.
I am using the NUS example as a base for my project.
2 services are provided by this application i.e RX Characteristic...
I'm trying to flash a Nordic Thingy. I have it connected to the debug port of a nRF52840-DK, nrfjprog --ids lists no boards, however.
However pyocd produces:
...
I have a question about bonding with "Peer Manager".
I am using the sample project "ble_app_multirole_lesc (SDK V15.3.0)".
I am bonding by "Peer Manager". When bonding...
Why does SPI not work with nrf_delay, from this previous question
devzone.nordicsemi.com/.../
Surely the SPI SCK is a PWM or other timer/interrupt driven clock?
Also...
When i use nrfutil to perform DFU it is passed, but when i send it through STM32 dev kit it Hash validation failed. but however i can see the CRC is correct.
Hello,
I have an AMS AS7261 light sensor that I'm using with my NRF51422 DK to take a light reading, pull it using nrf_drv_twi_tx/rx, and send it over BLE. However, when...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
I have few variables in application. These will...
i have a complete project based the gfx project and i want to add BLE using UART for communication. i want to communicate my module with the nRF52840 dongle.
is there simple...
SDK14+NRF52832.
I used one timer to do something every millisecond. and I used another function to do a loop action, the function maybe breaked if the time period exceed...
Can not connect Android 8 mobile phones, such as HUAWEI Nova 3
Nodic equipment is not even found.
We cannot connect with official UART routines.（ble_app_uart...
I found a terminal that can not communicate with BLE. I think that the sequence after MTU exchange is strange. The program used is sample HRM. The terminal used is "Xperia...
Hello!
Our current project is bare metal and has logging over CLI. I'm in the process of setting up a new project of ours that uses FreeRTOS but reuses a lot of the same...
Hello, I am using the nRF52840 dev kit. I am using SES to develop the code for it. I want to include the bosch bme680 library in my code. It comes as a libalgobsec.a file...
