Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
HI, we want to develop DFU over NBIoT network (UDP), and we would like some advice on how to implement that. We are using nRF52832.
Looking at your SDK examples for BLE...
Hello Everyone,
I am trying to integrate LIS3DSH accelerometer with nRF52832 development board(I2C communication). I have Implemented Wake-up State Machine for LIS3DSH....
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Hi folks,
I've found no beeter way of reporting this (no public SDK repo which allows issues with code reference).
I tried to TX ESB DPL frames from an nRF52840 to different...
Hi all,
I want to sell a device that I have made that uses the nrf51822 and the app inside the chip is derived from the ble_app_uart. It uses two chips that communicate...
When I send my app to people, it uses a specific version of pc-ble-driver. I would like to make sure dongle used was programmed with the hex file package with this specific...
Hi,
I'm having issues with my nRF9160. I followed the steps under "Getting started with development", but I keep getting the following error when updating the mfw:
I...
Hi
I'm using the NFCT peripheral of the nRF52832 Rev. 1.
The state machine (figure 118 in PS V1.4) shows that the NFCT can be activated by either issuing the TASKS_SENSE...
Hi ,
I am using the secure bootloader example (SDK 15) as a template for my DFU solution.
I am experiencing issue with the update process as the device shuts down after...
Hello
In our project we are using NRF52840 SoC.
Up to this point NRF52840 chip is used as BLE module to be able to connect our device to cloud over gateway.
now we are...
I have added DFU service in my custom application and I am able to upload the zip file of my application over the air by connecting to the DFUTarg using nrfconnect in my mobile...
I'm developing the PCB schematic for a system using the nRF52 and have some questions on the SWD programming interface.
It seems that I only need 4 pins for the Segger...
Hello,
I am curious, does nRF52832 support USB Type-C in terms of data transfer and Power Delivery? Or will I need another MCU to handle data transfer and Power Delivery...
Hi,
We've developed a custom board with buttons(peripheral) which will talk to another custom board operating as a repeater (central on one side to talk to our custom board...
