I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
Hi,
I am trying to set up SEGGER Embedded Studio for ARM and run secure_boot project.
All the time I have "Project load failed Reported error: solution load command failed...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52. And I am using Segger Embedded Studio to build and debug the code. But the IDE is unable to find the libraries...
Hello Everyone,
I am using nRF52832 with Softdevice S132 v5.0 and SDK 14.2.
I have been using ble_app_uart application as a starting point with SES. What i need now is...
Hi all,
I'm trying to learn more about the pairing and bonding procedures in the SDK. I connected one nRF52480 DK to my computer (running Ubuntu 16.04) and let nRF Connect...
Hi everyone, I have a nrf51822 Bluetooth chip that control a stepper motor, this Bluetooth chip can be powered by a maximum voltage of 3.6V, but I need a higher voltage for...
I have a split bluetooth keyboard that is using this firmware for the nrf51822 chips: github.com/.../mitosis-bluetooth
The general idea of the software is that the right...
Hi,
I am following the application note nAN-15 in which it mentions I will have to download NRF Probe and install but for some reason I couldnt able to find the software...
We're reading RESETREAS at startup from our nRF52832 cpu, and getting the value 10. The docs show that this refers to DOG and LOCKUP bits both being set. We don't have the...
Hello,
i'm using the nrf52832 with s132 and SDK15. I start the project take into account the example ble_app_hrs_rscs_relay.
The system is composed by 3 different services...
Updating firmware (application) from nrf Toolbox for iOS works fine (hex file), trying to do it from an Android phone does not.
The messages are "Starting DFU ..." then...
Hi guys,
first of all here is my setup: https://devzone.nordicsemi.com/f/nordic-q-a/42768/nrf51-52---sdk15---linux-gcc-st-link-v2
It seems like nearly none of the BLE...
HI ,
I would like to combine the Mesh client role with the Mesh provisioner role. That means, nrf52 application is able to switch between the provisioner and client (privisionee...
Hi to all,
i am developing a project based on PCA10056 dev board and i want use bluetooth and NFC in sametime. separately both of them work fine but when i want use them...
Hello everyone, I am planning to use the nrf52840 with the Fingerprint module (https://www.amazon.in/dp/B07DL2DXJX/ref=cm_sw_r_wa_apa_i_Z.VlCbXSSYVRS ). The sensor interfaces...
I got a new nRF51-DK board. I was planning on using USB to program it.
On the board I see pca10028 sticker. What is this?
Also in the SDK I see pca10028, and other pca...
