An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Per my another question:
devzone.nordicsemi.com/.../
I have taken the kind advice of Bjørn Spockeli but to no avail.
I tried this solution to enter debug mode:
...
I want to use the sd_ble_gatts_hvx() to send the notification with a packet, and the length of packet is 12 bytes, but the return value is "0x000C". I tested the length and...
Hi,
I try to run a dual mode(peripheral/central) with S130. I'm using SPI serialization and sending command form an external MCU. I try to follow the example ble_app_hrs_rscs_relay...
Hii all,
I am trying to work with dfu, I developing an application that works with dfu, when I flash the softdevice and bootloader the device advertising as dfutarg and then...
I've loaded the S210_nRF51422_5.0.0 softdevice on my board from the nRFgoStudio.
I compiled the ant_hrm_tx_auto_s210_pca10028 project with no problem. However, when I try...
Hello,
I am developing two systems. One is a peripheral that advertises both a beacon and a ble peripheral custom service (using nRF51822 with s110 softdevice). The second...
Hi,
I am trying to use an nrf51822 with a sensor that outputs value between 0-5V. What I am confused about is how to read input voltage on the beacon. I saw some people...
Hi,
I need to debug my perpheral device, but as I know if I do debug when SD is running, it can cuase the time sync issue, then cause the hard-fault. I know there's a way...
hi ken：
I use Nrf52832(S132) to act as central and peripheral at the same time, which like the project ...\nRF52_SDK_0.9.0_0c82e3e\examples\ble_central_and_peripheral\experimental...
Hi,
I run ADC mudule together with SD, but go into hardfault eatch when I release the HF-clock.
Chip: 51822
SDK : 10.0-alpha
IDE : Keil-472
I use this function...
Hi!
I have inherited a large codebase that I'm trying to migrate to SDKv10 from SDKv6.
The project also uses an A4960 BLDC motor controller. To bring the motor up to...
Hello,
Is my ram reservation right for nRF52 with S132 ?
see in app_ram_base.h APP_RAM_BASE_CENTRAL_LINKS_3_PERIPH_LINKS_1_SEC_COUNT_3_MID_BW = 0x2F50
RAM (rwx) ...
Hey,
I have been trying to create a notification characteristic for nrf51822. Whenever I add char_md.char_props.notify = 1; lightblue doesn't connect to it.
I do get a...
Ok, this one seriously has me stumped...
I have a custom bootloader that is modified from the DFU example (SoftDevcie S110 8.0, with SDK 9.0, using gcc). BLE is not used...
