I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
Hi, i was working with this project where i'm trying to make the thingy53 a thread node.
when i build i find this error and i don't know why:
Building thingy_coap_server...
We have recently switched to using the nRF Connect SDK. Our application is based on the "Peripheral LBS" example, and after several iterations, the code has started crashing...
I use nrf connect SDK.
zephyr/include/zephyr/bluetooth/direction.h is not include "extern "C"".
So, It's can not call from C++(cause link error.)
Any reason why?
Hello,
I'm developing FW based on nRF52832, SDK 17.1.0 and SD S332. I need to set up ANT+ comunication to use my device as a display for LEV profile (I started modifying...
I am developping a scanner to detect advertisements from all BLE objects in the room to collect data from the advertisement data.
Some of those BLE objects are broadcasting...
Hello,
I am currently working on a project that is set up similar to the Thingy91 LTE BLE Gateway application (Bluetooth HCI UART firmware running on nRF52840) and I am...
Hi,
we have designed nrf9160 custom boards.
i have upload he AT_CLIENT example but i'm not able to get response when i send commands. total i have 2 custom board but i...
Hi,
I'm testing the Zigbee cli example and is trying to connect to a Danalock lock but get an error when the lock connects to the coordinator.
I have used these initial...
Hi:
The MCUboot supports USB CDC and UART recovery, and we also can upgrade the FW via BLE and UART normally at the application level.
I would like to know if the normal...
Hi
I need to evaluate my project which is based on a peripheral sample from zephyr, I am using thingy53, so my thingy53 is sending the data over ble to the mobile app for...
NRF52 on custom hardware
SDK 17.0.1
SoftDevice 7.2
I have a timer running, one shot or repeated, that blinks an LED.
It works just fine when run from the debugger...
Hi,
suddenly our PPK2 stops working and we started to have strange values on nRF Connect interface (current values in YA...).
This screenshot has been taken with a connected...
Hi all,
I'm aware that the typical current draw is about 15 uA in "sleep" mode, 56 mA (Rx) and 165 ma (Tx, +15 dBm, 2.4 GHz). This is according to Nordic Webinar and Fanstel...
I made an NRF5340 board with NRF7002 myself. No external flash is used on the hardware.
Try running the light_bubl sample for ncs2.2.99.
I'm using this custom board with...
Hi,
I'm making progress with using the UARTE in bare metal programming. My goal is to have maximum control over my system and provide a reliably and robust realtime implementation...