The OSCILLATORS documentation says:
" The device starts at 64 MHz. For 128 MHz, it must be configured when the CPU starts and before any peripherals that use the high-frequency...
Hello,
I am using nRF54l15 and nRF Connect SDK v2.9.0
I need to know if there is any way to disable the cfg_changed callback at runtime. I want it to be called in case...
I am in the process of getting a Nordic Thingy 91 X up and running for an upcoming development project. However, I’m having some problems getting the Thingy to connect to...
I had to modify the modem_cellular.c file driver in Zephyr to make it work for a SIMCOM modem. I know I could try getting a PR to Zephyr approved but it'll take some time...
Dear Team,
I am experiencing issues updating the firmware image on my custom board based on the nRF7002, using an external SPI NOR flash ( is25lp064 , 8MB). The board...
nRF52810 will not enter deep sleep (system level power management). The method used is through pm_policy_next_state, sleep entry function , sleep exit function, and PM notifier...
NRF52840DK NCS 2.8.0 Hello , We are developing an application where a device with router function must join a coordinator network. The coordinator uses OOB (proprietary IR...
Hi,
In micro_esb.h, it is indicated that the transmission without ACK is not implemented yet. However, there is a parameter named dynamic_ack_enable in the uesb_config...
Hello,
I am getting a 0xdeadbeef assertion at src\soc_radio_timeslot.c line 390. I am using S110 SoftDevice v7.1.0 with nRF51822 revision 2 CEAA. I am using the multiprotocol...
Hi,
i'm newbie to ANT world and i'm trying to create a mesh-like network using broadcast messages and shared channel with nRF51422 SoC and S310 soft-device.
So, i created...
Hi all,
I've been trying to develope a project by using an nRF51822 chip. The project is about to finish. However, I couldn't implement the pstorage module in a correct way...
I am looking to re-install the firmware on my dongle after making it a sniffer but I can't find a hex file for PCA10031. My MasterControlPanel has firmware for PCA10000 should...
Hi
Should I get a characteristic write event ( BLE_GATTS_EVT_WRITE ) with s110 as well with the
following property configuration:
char_md.char_props.write = 0;
char_md...
I try to achieve something similar to IBeacon where data is pushed to any device listening, but where the data is changing over time. Is it possible to (frequently) change...
Hello,
I have recently had to install the nrf tools on a mac computer. The tools have been recently ported to macs, but unfortunately I am getting the following message...
Greetings,
During a connection between two nrf51422s running on S120 (2.1.0) and S110 (8.0.0) with a connection interval of 7.5 ms I get only a maximum RSSI of -42 dBm...
Hello,
I developed a firmware on nrf51422 with nrf51. I use a development board PCA10028.
With this firmware I control the directly the radio registers (Soft Device is...
I have a nRF51822-EK evaluation kit (so, PCA10001) and am trying to get DFU working with an S120 SoftDevice as per the answer posted here:
devzone.nordicsemi.com/.../ ...
nRF51822
I'm interested in setting up the the POFCON to enable me to get a
POFWARN interrupt when the battery voltage drops below 2.7V.
The softdevice is enabled at...
I have a nRF51422 dongle, and I want to know the power/current when an UART event happens.
I've read nRF51822_Development_Kit_User_Guide_v1.4 p.29 for Current Measurements...
