We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello,
I recently updated the asset tracker on my thingy 91 with the lastet available pre build firmware (2019-11-29_d3130d77) using MCUBoot.
Since my Thingy91 is only...
I started with the mqtt_simple example.
I added:
#CONFIG_MQTT_PASSWORD="pass" #CONFIG_MQTT_USERNAME="David"
to the prj.conf file. Relaunched the project which rebuild...
As a matter of fact that there is no special EEPROM in nrf52832 , the user data which need to be stored in nrf52832 should be written into the flash of nrf52832 . The SDK...
When debuging nrf52832 , the code can be flashed into the flash through JTAG . However , I need to reprogramme the nrf52832 through UART interface . It seems that there is...
Hello.. I use RNF52840 Dongle. I compiled the blink example with VS code and I programmed with nRF Connect tool.
now I can't connect the USB device. I read that I had to...
Hello,
I am currently aiming to create an application for the nRF52-DK using the nRF5 SDK and Segger Embedded Studio as my IDE.
Due to the SDK itself being extremely extensive...
Hello ,
I have been trying the Zigbee CLI light example.
And I modifed the main.c file to have the network saved "ZB_FALSE" and then flashed the updated hex file to 52840...
Hi we are having issues with gpiote interrupt. We would like to do some spi read when drdy gpio becomes high to low. I have done above configuration for the same.
We are...
I have a problem collating model publish events arriving at two different nodes in my mesh.
My application is an array of sensors publishing through generic on off and generic...
Hi,
I have a custom board running NUS peripheral which uses the nRF52832 and a NUS central which is running on a nRF52 DK. I modified the ble_app_hrs_freertos example to...
Hi,
I found the communication range using FREERTOS is shorter than which are using non-RTOS.
I know the RADIO TX power and the PHY rate affect the communication range...
Hello,
I am using nrf52832 Dev Kit and am attempting to send information using the ble_app_uart example under SDK version 15 (I don't know the exact rev, but I downloaded...
Hi,
I am using nrf52832 in my custom board and I want to make secure connection between my two boards using stored keys.
Is there any example provide by nordic which I...
I am using the nrf51822 ble with s130_nrf51_2.0.0_softdevice and want to know if the broadcast can start at a given time, and if the adv_ interval can change everytime? (such...
