At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Issue
How to properly wake an nRF54L15 from System-Off mode when the device receives a UART transmission, without the use of the LPUART Ready and Request lines or any sort...
Board: nRF52840 DK (pca10056) NCS version: v3.2.3 Goal: Send and receive raw 802.15.4 frames with a custom packet format, without using OpenThread, Zigbee, or any other mesh...
When attempting to install a downloadable app in nRF Connect for Desktop 5.3.0 on Linux, the installation fails with an EISDIR: illegal operation on a directory error. The...
As mentioned in subject,I try to study course with CMSIS-DAP,now, chip recove and flash is OK,but blocked at debug step for 2 days now.
Maybe I made some wrong config some...
In nRF cloud, in the device list ( https://app.nrfcloud.com/#/devices ) it is difficult to manage larger number of devices because of lack of search and limited sorting. ...
This question concerns the description of the SPI communication Electrical Specifications on page 425 of the nRF52840 Product Specification.
The values for "t_spim_vmo...
Hello,
I have a product with QSPI flash that I would like to use nrfjprog to program the flash part. However, the QSPI flash's VCC is controlled (via a FET) from a GPIO...
Summary
With CONFIG_OPENTHREAD_ZEPHYR_BORDER_ROUTER=y and CONFIG_OPENTHREAD_TREL=n , the Zephyr/NCS build fails to link:
ld.bfd: ... openthread_platform.a(trel.c.obj)...
Hello,
I am currently working on a new design based on nRF9151. This design is the evolution of a previous PCB.
The device uses a combined GPS and Cellular antenna, which...
Subject: Support Request for nRF7002 Integration with ThreadX on STM32
Hello Nordic Team,
We are currently using the nRF7002 with our STM32-based device. We have completed...
I am using nrf52832, and I want to use SYSTEM ON Sleep. Also , my wake up sourses are timer based, and also GPIO interrupt based. But I observed that the device cannot go...
Hey there!
I am currently in the process of trying to setup a simple ISR routine triggered via GPIOTE.
However, when calling nrfx_gpiote_init() or nrfx_gpiote_input_configure...
Hi together!
In my current project I would like to send some sensor data to an Azure IoT Hub, by using a nRF52840.
In the first step and for evaluation I used a nRF9151...
