Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I am trying to use the ArrayList Feature of SPIM. From my unterstanding, it simply increments the pointer to the memory address every time the START task is triggered...
Hi,
my setup is the following:
- SDK 2.6.3
- nRF5340
- Low power management for external flash enabled
- Logging enabled (based on littleFS)
- external flash used...
Hello,
I’m wondering if there is a way to forward data from RTT to a COM port on Windows.
I’m currently evaluating the GPS performance of my custom PCB using the GNSS...
I have a very simple product which consists in a Xiao Nrf52840 board (which is FCC certified) wired to a 5v relay module. I was wondering if I would need additional FCC certification...
Hello, I am trying to add GPS functionality to my program running on the Thingy:91. However, I can't find any examples except for the Asset Tracker, which seems overly complex...
Hi,
MCU - nRF52832
I am trying to understand the power consumed during the PaWR operation. I am referring to the steps explained here: I am getting the a similar graph...
We currently have several nRF52840-based devices deployed in the field, running firmware developed using the nRF5 SDK and utilizing the SoftDevice S140 for BLE functionality...
Hi Team, I am trying to see the PaWR PDUs in wireshark sniffer. I am using example periodic_adv_rsp from NCS v2.9.0. I am referring to the link for exploring. How can I see...
Dear Nordic company,
I am writting to you in order to get some information about buffer sizes in your aplication. I think, I am bale to modify buffer size and maximum...
I am designing an application using the nPM1100 and I would like to know if I can use the VSYS as a power supply pin for my other circuit.
Is VSYS supplied by the battery...
In the nrf_sniffer_ble.sh script, the block that checks for an active virtual environment uses the following line:
if [ ! -z " $VIRTUAL_ENV "];
Notice that...
Previously, I compiled and downloaded the radio_test example into two DK boards.
I then used the CLI to set the parameters for each board one as TX one as RX
On setting...
1. Can we use SIM other than iBasis to use nrf cloud?
2. My SIM does not have a PUK. How to proceed without entering it.
3. We need SIM too kit document for nrf9161. ...
We are using the nrf52840-based module in our product.
This module is already certified with BT SIG.
Do we still need to certify our product with BT SIG certification...
