We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hi,
I am using NRF MESH SDK V3.0 ,nRF5_SDK_15.2.0 and with s132_nrf52_6.0.0_softdevice .
I've noted some problems when i try to use the app_timer in repeat mode with a...
Hi Team,
I transplant the project Uart from example/peripheral/uart tranplant to blecentral/multilink project, but it does not work, it indicate that APP_UART_COMMUNICATION_ERROR...
Hello,
In below link, I am bit confused between “With bootloader” and “Without bootloader”. What for this bootloader.
https://infocenter.nordicsemi.com/index.jsp?topic...
Hi all,
I purchase a Li-Po batter where it will output 4.2V when I connected to nrf52480 DK, it causes all 4 LEDs (LED1, LED2, LED3, LED4) not functioning anymore.
The...
Hi,
I have the latest 0.4.0 tag, flashed the latest modem firmware 0.7.0-29.alpha, and debugging the asset_tracker app under nrf9160_pca10090ns.
When I debug the app it...
Hi,
I'm using the latest everything for the nrf52840 with SES.
When I define a global variable that require substantial memory I get the linkage errors:
. bss is too...
Hi
I want to run the the HTTP application update sample on the nRF9160. SDK v0.4.0, SES V4.16, Win 8.1.
I can build and run the application on the DK but I don't find...
Hi,
We have worked with building a raspberry pi system that uses a nRf52832 dev kit board and the pc-ble-driver-js code to scan and connect to our bluetooth devices. This...
Add whitelist function in \ nrf5_sdk_15.2.0 _9412b96\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay, and report error 12804 (0x3204) after disconnection...
I'm trying to use the SAADC to return one value so I initialize it, try to take the reading, then unitize it so I can use it for taking readings through the PPI. The SAADC...
By default, is it enabling or disabling bias correction? If no, how to enable bias correction?
Is the RNG peripheral being left on all the time as a result of us using it...
hello,
I need send 10000bytes large data send central to peripheral in single transmission. I using example code ble_app_uart_c in SDK15.2 nrf52832. what are the parameter...
Hello
I am writing low-power application where NRF is called from the other chip by interrupt, performs bluetooth scan and sends data back over UART. Of course, I want to...
