I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
It is possible to run easily a SoftDevice stack (e.g. S110) on nRF51422 using an accurate 16MHz external clock reference for HFCLK instead of an external 16 MHz crystal oscillator...
Hi,
I am working on implementing concurrent BLE UART central and peripheral service. I am doing this by taking "ble_app_hrs_rscs_relay" default example as a reference. ...
Hi, how i can mark internal flash memory nordic for user data and logs, and protect them from being overwritten when updating firmware over the DFU?
Thanks!
hey nordic,
it has been 10 days since there is no reply.
please any nordic engineer reply in this thread
https://devzone.nordicsemi.com/f/nordic-q-a/45470/encryption...
Hi,
We are developing a new internal engineering tool that mostly does passive scanning on the NRF52840 dongle connected over USB but I'd like to be able to switch to...
The relay successful rate of my Mesh setup is not 100%. I think light server miss packet from light client. I have tried to change configuration following:
1 #define BEARER_SCAN_INT_DEFAULT_MS...
HI,
We are currently using System ON mode with RTC is running, and we are not facing any problem. But our concern is power consumption
We are using below peripherals with...
Hi,
I am try to send many data via ble_nus_data_send() function, but I found "Host can not receive any data if ble_nus_data_send() is execute busy".
So, I have two questions...
Hi to all,
I am developing an app based on nordic NRF52840 soc and i want to implement a peripheral device that can connect to multiple central devices in same time and...
Hi,
I'm using nRF52840 and I have some issues with direct advertising.
When I'm using fast mode advertising everything is OK. While using direct mode, I do everything...
Using SD 6.2 and sDK 15 I need to write to the UICR_Customer space while the BLE system is operating.
I tried pulling example code from https://devzone.nordicsemi.com...
Hi,
I want to program my nrf52 DK through OTA programming. In my project I don't use Bluetooth.
Is it possible to program the board using the Radio without a Bluetooth...
Does anyone here can share the source code for a small program written in C or C++, which can be compiled on a Windows machine, and can receive the orientation data from a...
Hi. I have just installed the new windows nRF connect 2.6.2.
How do you do secure DFU? There are no apps in the list to do that. On your website it says it supports DFU...
In my attempt of learning the nRF52 "eco system" (nRF52 DK, nRF15.3 SDK, SES and pca10040e project for nRF52810), I have combined the GATT_C, GPIO and SPI examples to make...
Device/SW Info:
Ubuntu 18.1 SDK : 15.0 SD 132 v 6.0
NRF52832 QFAAE1
The device once connected to the device is immediately dropping the connection upon going into...
