I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
Hi,
I've loaded SD 8.0.0 on the device, but when I try to load application via NRF Studio it always fails.
Im using SDK 10.
Memory settings in Keil:
IROM: 0x18000 0x28000...
I use s110 v8.00, now i need finish the dual bank ble DFU program.
who can offer a example?
the s110 v8.00 is use nrf51422,and used the ram2,
I compile the project,find...
I would like to be able to manually disconnect from a device and then begin advertising.
However, I have discovered that on disconnect, ble_advertising_on_ble_evt handler...
I have an application using N5150 SOC with S210 softdevice and using softdevice_handler, SDK 10.0.0.0, and I'm using Ant-FS to gather data from this device. I only want to...
ble_app_beacon.rar hello there i used ble_app_beacon example. i want to make some modifications. i want to put it in sleep mode after some time and again wake up after some...
Hi,
I am trying to run the example ble_central_and_peripheral_experimental (SDK 9), I program the device with S130 and the hex file. The other two devices I program it with...
Hi,
What is the meaning of "NRF_CLOCK_LFCLKSRC_RC_250_PPM_250MS_CALIBRATION"?
It means use the internal RC clock source, but what is the meaning of "250_PPM_250MS_CALIBRATION...
My application uses the WDT. In my application, I use a soft reset to enter the bootloader. Because the soft reset does not reset the WDT the program will reset while in the...
Hi, current i'm writing a program in nordic nrf51822 chip and I facing the problem of region RAM overflowed with stack after adding the BLE code as shown below :
//***...
I have a RFID application in which there is a Reader and a tag. The Reader reads the tag information once the tag is in the Reader's range. The tag is an active tag.
The...
I'm working with app_fifo_uart and I'm seeing that my event handler gets the event 'APP_UART_TX_EMPTY' repeatedly. Multiple times a second. Is there any reason for this? Can...
I am using my nrf51-DK with mBed for prototyping. I noticed recently, that the DK had stopped broadcasting a BLE service, so I followed instructions to update the firmware...
I was under the impression that HomeKit was an extension of the MFi Accessory Interface Specification, which relies on the iAP protocol to access additional functionality...
Hi, I'm trying to run the ble_app_uart_s132_pca10040 demo but I can't get it to work.
We're using Keil 5.17 and downloading the example from the pack installer.
The packs...
