We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hi,
Our application includes implementation of capacitive touch sensor through SAADC.I should initially wake up device from system off mode.Using SAADC is it possible to...
I found on GitHub an nrf52832 Bluetooth course, can I use it to learn how to use the nrf52840 DK? Currently, I am having some issues on learning how the use the nrf52840 DK...
Hi,
I'm trying to utilise UART1 and freertos queues, with dynamic b;e&threads.
I'm trying to use the serial api for the UART.
I've tested the code below with the freertos_coap_server...
I have to send 6 bytes of sensor data from mesh server to mesh client. Is it possible to use simple_on/off model or have to create new model. Any sensor model example is available...
To the kind attention of Nordic support team,
I'm experiencing some problems switching off in a clean way the usbd library/usb driver/USB peripheral. I do need a clean switch...
Will Nordic provide the official implementation of models in the mesh model specification, which include the Generics, Sensors, Time and Scenes, Lighting models?
Thanks...
Hello, I have to work on a project concerning the Bluetooth Low Energy ( https://github.com/bjornspockeli/custom_ble_service_example )
If you already worked on it, I hope...
Hello,
I have some questions on power removal on nRF52832 chip.
I think that some tasks are managed by the application and some other directly from the stack, the firsts...
Hey,
I have a product which is using nrf24l01+ for communication. There is packet loss in the communication which I am trying to figure out the reason for. Is it possible...
U-blox NINA-B111-04B is being adopted. (Nordic Semiconductor nRF52832 is used) For product evaluation, I would like to connect with Anritsu BLE tester MT8852B for evaluation...
Hi all,
I am continuing with university project now in its 4th year of development for a wearables leg motion measurement application. Two trackers with identical hardware...
Hi,
We have a bluetooth product which uses Nrf52840 as the MCU. It composes of a peripheral and a central device of which connect with each other via bluetooth and they...
Hi,
We have a bluetooth product which uses Nrf52840 as the MCU. It composes of a peripheral and a central device of which connect with each other via bluetooth and they...
Primarily addressed Torbjørn Øvrebekk, Nordic.
Refer document nRF52 832 Product Specification v1. 4
I read " The same block in the Flash can only be written n WRITE number...
