Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
nrf51822 device obverse six bytes mac addres could change，when OTA failed.
six bytes mac address, five bytes fixed, one byte can change when OTA failed.
Now，my app...
Hello,
I am using Nordic Nur-10W develop kit, trying to compile NurApiExample in Raspberry Pi. I wrote a Makefile, and complie process was OK. However, undefined reference...
hi
im using sdk v6 and when i turn my board on it goes to bootloader and i can upload my program into it .
the problem is that i want it to run to my main program after...
Hello,
I would like to use a custom flash memory layout for the flash memory of nrf52:
I thought that I should be able to use the UICR.NRFFW[0] - if I set to the start...
Hi, I use PCA10040 v1.1 with SDK12.1 via S132 v3.
I use Keil 5.21.
After testing the LBS example, I was merging the NUS (NORDIC UART Service) to the standalone LBS example...
I am working with nrf51822 board softdevice of s130,sdk11.0 version.I want to create 4 KB of Flash through PStorage.I am able to create 1 kb(maximum block size ) of flash...
Hello everyone,
I'm doing some work in SDK 12.1 and noticed that even the example peripheral project "ble_app_template" compiles to 26K under Keil. Given there is a 32K...
Iam using SDK10.0 and Softdevice version S110, i use device manager to monitor connections, i have implemented passkey pairing. nRF board is peripheral and iam connecting...
I have a project using printf to send AT commands to a cellular modem. It works well.
Yesterday I added Segger_RTT into the project.
With NRF_LOG_USES_RTT=0 defined.
...
I'm trying to get an a recognized ble pulse without using a softdevice. I started with the basic transmitter application and am trying to decipher the order for the data I...
Hello,
I am trying to get my device (nrf52832) to do DFU OTA, and to do so I am programming the bootloader before programming the s132 softdevice and the application. However...
Dear Colleagues,
I am much obliged for your kind assistance to me.
My Question:
I have setup my NRF8001 successfully (please find the setup file generate by the nrfgo...
Hi,
I use SPI Master driver to communicate with a flash memory.
I use SDK 12 and i use nrf_drv_spi_transfer(...); to write and read over SPI.
My problem is the following...
We are using SDK 11 and SD v2. I did a search for an answer to this question, but couldn't find one that addressed it fully but what I gleaned is that this may not be possible...
