Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hi
I am trying to start an advertise. If I use the “BLE_GAP_ADV_FLAG_BR_EDR_NOT_SUPPORTED” flag all work’s pretty fine, but whenever I change the flag to “BLE_GAP_ADV_FLAGS_LE_ONLY_LIMITED_DISC_MODE...
Is it possible to have a fast advertisement interval (for connecting and bonding/pairing) for example: 40msec; at the same time, have a slow connection interval (after connection...
uint8_t flags = BLE_GAP_ADV_FLAG_BR_EDR_NOT_SUPPORTED |
BLE_GAP_ADV_FLAGS_LE_ONLY_GENERAL_DISC_MODE;
And then when I look up "BLE_GAP_ADV_FLAGS_LE_ONLY_GENERAL_DISC_MODE;...
Hallo,
i'm trying to test my BLE aplication using the PTS. The profile test are mostly OK. But if i run the GAP Test (especially TC_BROB_BCST_BV_01_C) the PTS does not...
It seems that static and global data is NOT set to zero during start-up. This is supposed to happen according to the C-standard. How to do this in a proper manner, i.e. to...
Hi All,
we currently move our custom design to CE testing and already did some successful EMC pretesting.
However, our testing house asked us to prepare a firmware for...
Hi All,
BLE Nordic Stack: 0.9.7
Tiny Circuits: Ardunio + Nordic nRF8001 Board
First time post, and hoping someone has run into the same issue that I am. I am in the...
Hello!
I am working with the example mpu interface projects located at the following repo:
github.com/.../nrf5-mpu-examples
After converting the Keil projects to...
Hi,
After I've successfully connected my smartphone via nRF Toolbox's UART-BLE Service to my nRF52 peripheral, I tried to mimic the scenario when the devices get disconnected...
Hello
I want to understand how far the firmware that is burnt on to a Hardware is protected. Is it possible to actually read the firmware from a device (if the device has...
Services Setup
I am trying to feed the "Services Data" manually to the nRF8001.
As per the data sheet page 82 (see image below): Upon transmission of 1 packet of data...
I am trying to run the ble_app_beacon example on an nrf51802 device.
The call to sd_softdevice_enable() never returns (jumps to 0xFFFFFFF9)
The fault handler is not called...
My guess is that:
Characteristics are (or at least, can be considered) subsets of services, which in turn, are (or at least, can be considered) subsets of profiles.
...
Hi, I am modify the S120 multi-link UART example code (code is available here ), and just noticed a problem that the central is only able to send the UART data to the last...
