This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
I'm sending Data from nRF51822 to nRF24L01. The configuration of the nRF51822 is NRF_RADIO->PREFIX0 = 0x43434343UL; NRF_RADIO->BASE0 = 0x43434343UL; The address of the 24L01...
Dear support team, I would like to simultaneously use logging and CLI via UART in an application running on the NRF52810 with Softdevice S112. In my application, I need to...
Hi
I am having a problem debugging a basic UART code.
I am using Segger-16 for Nordic, and I have an issue with #include "app_uart.h"
I downloaded the nRF_SDK_17.0.2...
Hi,
could some one inform me how to create a bare metal project for nRF5340 (Network Core/Application Code)? The specification gives everything to create an own stack on...
Hi there!
I'm having an issue adding WiFi functionality to my project. I use the nRF9160DK and the nRF Connect SDK v1.5.1 on a Windows10 platform.
To keep it simple i...
I am using nrf52DK board as an observer to test my beacons. I have kept scanning enabled all the time (scanning interval & scanning window same), but the scan_evt_handler...
I want to use the nrf5x to develop the host/gateway of bluetooth mesh, may I ask which model is more suitable, which model currently supports the most mesh nodes?
And which...
Hi Nordic team,
I have successfully developed an application using nrfx (Timer/PPI/SAADC) combo in NCS 1.5.x to be able to sample 2x differential channels very fast.
Similar...
I have trouble developing BLE devices with Nordic NRF5280 and SDK 15.3.
I have a device that uses a custom BLE service, And when using nRF Connect on the mobile phone, all...
I have been developing some nrf52832 code (SDK 17.0.2) using the Segger RTT debug window for logging. I added the code from the UART example but the printf goes to the debug...
I'm planning to modify the nrf52832_ciaa reference designs in altium to emulate the functionality from a development kit and add an RTC.
I need access to pins P0.23, P0...
Hello. I would like to use an internal RTC to keep time going even if the power is off.
1. Is it possible to implement with 'nrf_calendar' module?
2. Should I think about...
I have a battery powered iOT device using BLE, I2C, and GPIO. I am focused on reducing the power consumption. When BLE is not connected, I want to have as little power usage...
This is in response to a central sending an update. I try and follow with the central's request except I set the times to the AUTO value. If I get an NRF_ERROR_NOT_SUPPORTED...
