Hello! I'm using sdk8 and s110. I want my peripheral device to send data to the central. I doing following steps:
1. initialize service:
void services_init(void)
{...
I am glad that I have successfully used the library from www.libstock.com/.../nordic-semi-nrf24l01-example in a pair of PIC18F45k50 devices. One is acting as a Tx and another...
Hello.
I have had a search but can not find anything so sorry if this has been covered before.
Our company has developed a consumer product using the nRF51822-QFAA-R7...
Hi every one !
I am trying to get working a code that it was working "Ok" 2 years ago.
Currently, I cannot get communication between both breakout boards.
To simplify...
I'm trying to solve an intermittent problem when using the nRF51422 UART with CMSIS-RTOS (RTX) and MDK Networking library (V6.2) (TCP/IP stack).
My questions relate to...
Hi...
When i was working in SDK v6.1.0 i have tried nrfprog.exe to merge and program bootloader, softdevice, application and bootloader_settings file as explained in devzone...
I am testing the NRF9151-SMA-DK NTN function using the mfw_nrf9151-ntn_1.0.0 firmware and serial_modem_v2.0.0-preview1_nrf9151dk_normal_mtrace app. I keep seeing
%MDMEV...
HI,
I'm reading this post about NFC antenna matching. It says in Method 1 to connect the coil antenna to the S11 port of the network analyzer. How should I make the connection...
I am currently working on a design with the nRF9160, and have a few questions about the DEC0 pin and decoupling for the module in general. I have been considering adding additional...
I keep seeing this in your documentation:
This functionality is in the process of being deprecated and replaced by Zephyr’s default devicetree-based memory partitioning...
Hi,
I am testing the radio_test (short-range) sample on an nRF54LM20A DK . The test setup is:
Board: nRF54LM20A DK
Sample: peripheral/radio_test (NCS version...
Hello Nordic Team,
I am evaluating the nRF54LM20B physical DK using nRF Connect SDK v3.3.0‑preview2 . In the SDK, only the nrf54lm20apdk board target is available, and BLE...
Hello, I am working with the following sample project and NRF Connect SDK v3.3.0. (Referenced regarding this topic .) The sample implements DFU with MCUBoot while using the...
I am evaluating the output power of a testboard that uses the nRF52840-QFAA.
The matching network closely resembles the recommended network in the datasheet (shown in figure...
Hi!
I am using MCUBoot and the DFU library to perform a custom firmware update (which is working as expected).
I have a question about the "swap_type" value, which is...
Hi Nordic team,
I’m seeing a repeatable configure hang with NCS v3.3.0 sysbuild on macOS. The visible build output stops after:
After inspecting the process tree, CMake...
Hi,
I am currently working on a research internship project using two nRF9151 DK boards and one nRF9151 SMA DK. My goal is to establish device-to-device communication between...
Hi Team,
I need to use this external clock for my deep sleep use case so let me know the step forward for the same.
I am using custom board with nRF54L15 and also LXFO...
HI all,
The main program suddenly encountered assert （nrfx_grtc.c line 278）while running, which happened by chance. The following are the relevant logs
note:nrf54l15...
Hi, all!
I'm currently facing an issue with upgrading the nRF52840 firmware on a Thingy91 and would greatly appreciate your guidance. I'm following the official instructions...
