At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hi,
I'm having issues getting code to run using nRF51 SDK 10.0, on an nRF51822xxac.
I am using the pca10028 ble_app_hrs_c example, and the inculded softdevice "s130_nrf51_1...
Dear all
I am currently working with a nRF52840 Dongle, the ble_app_blinky_s140 example.
To power some external circuits i have to set VDD to 1.8V.
Until now i tried...
hi, this is Shivaji, I have to work on Bluetooth mesh, so which kit I have to buy, can I buy thingy52 or can I buy nrf52dk. which board should I buy, and can get the android...
Dear Sir,
I have bought a BMD 300 chip.
I have implemented a firmware with segger embedded studio and SDK15 for nrf52832.
I have flashed it to BMD300 DK from Rigado...
Hi:
As we are going to use nRF52840 on our product, we were trying the check the HW security implemented in the chip. nRf52840 implemented Arm TrustZone CryptoCell-310 in...
Hi Team,
I hope you are doing good.....
I am using nRF51822 with the SDK version 12.3.0 in windows, keil version is 5.26.
In the blu_app_uart Application i want...
Hi,
In order to isolate the issue, I've created an app that :
1. switches to dc2dc mode.
2. calls sd_app_evt_wait()
I still see 3ma consumption,
any ideas...
Hi
Actually i have a big project and have a problem in the estimation of FLASH and RAM memory for the project
i ma going to implement the mesh SDK with the BLE Stack because...
Hello,
I am working with a custom board with the nrf52832 chip.
I have merged and written the following on the board: SD (s132, 6.1.0) + secure bootloader from the latest...
Hello,
I purchased a nRF52 DK board and sparkfun nrf52832 breakout board , and was successful with blinking the LED on the breakout board.
In order to test if I would...
Hello,
(I am using SDK 15.1 on a linux system)
I will breakdown the question in two parts -
when do we get fatal ? - i know one or two cases for example when softdevice...
Hi.....
i want to transfer the data for every one minute from peripheral device to nrf connect via (phone app).. how to declare in the program and what function to be used...
Dear all,
When I added more than 4 buttons by modifying the example "ble_app_uart" of nRF5_SDK_15.2.0_9412b96, nRF52832 can not run normally.
Another strangely problem...
