We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi we are integrating a ANNA-B112 device from u-blox that use the nRF52832 core. The pin mapping for UART appears to be different for the Software (not open source) that they...
I have a general question that I haven't been able to clearly locate in documentation. How does the processor handle "traffic" jams from within the different app timers? ...
Hi everyone, so I have been trying to enable the nRF52840 to send notifications to the Nordic Connect app via a custom characteristic. The app can detect the custom service...
Hello,
I have an issue opening the power profiler kit 2 on my windows desktop:
Somethimes it works after restarting, but stops working after a few minutes.
After it...
With a baudrate of 1000000, when i transmit 2 subsequent packets (with ACK), i have to put a delay of 0.2 msec or more. Otherwise the second packet will get ACQ packet acknowledge...
We're trying to debug an issue with our nRF52 chip when pairing to some Android phones. On the nRF52 we are connecting to mobile devices by acting as a peripheral for the...
Dear friends,
I used a serial bootloader by this tutorial Secure DFU Bootloader over Serial Link (UART) , i can upgrade my application with the pc nrfutil tool, the nrfutil...
Hi sir,
I have a question for Bluetooth 5.1 single mode. As I know, above Bluetooth 4.0 has single mode and dual mode. Single mode only supports LE and dual mode supports...
Hi.
I'm newer on Zephyr.
I want to use the LOG Output.
LOG_DBG("main.c"); LOG_INF("main.c"); LOG_WRN("main.c"); LOG_ERR("main.c");
Everything works but the color of...
Hi everyone,
I'm developing a new application/product. It will feature a nRF52805 without the LFXTAL but with DC/DC support. I'm developing with the NRF5 17.0.2 SDK.
I...
Hello,
I am trying to commission a device running the CLI sample to an OTBR I configured following https://openthread.io/guides/border-router (the OpenThread official guide...
Hi
in Zephir nrf9160dk_nrf9160_common.dts the SPI pins are defined
&spi3 { compatible = "nordic,nrf-spim"; status = "okay"; sck-pin = <19>; mosi-pin = <18>; miso-pin ...
hello,
i am using nrf52832 with sensor which uses uart communication and using sdk 15.2 but i could not get my excepted values in rx buffer which is of 3 bytes and values...
