This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hey guys,
I'm working on a project and want to build up on the Nordic BLE UART example (mobile device app and node firmware). As far as I know the pairing between the node...
hi all,
I have added the dfu service in one of example of sdk_11 ble_scanner_hrs I followed all help available on this forum and made sucessfuly compiled code but it stopped...
Here is a thing that I want to develop.
As my understanding, if I want to connect with PC I must use the HID example to achieve the event.
However, is it possible that...
I programmed an nRF52 (PCA10040) with the ble_app_beacon sample app and can see it advertising. However the nRF Beacon Android app does not detect it. nRF Beacon seems designed...
Hi,
I have a nrf52840 DK (pca10056) and a nrf52840 Dongle (pca10059).
I am using the following SDK versions:
nRF5_SDK_15.2.0_9412b96
nRF5_SDK_for_Thread_and_Zigbee_2...
HW: nrf52840
SW: nRF5_SDK_15.2.0_9412b96
Hi,
I would like to learn how allocate Flash, RAM and SRAM setting and how do I find out the total RAM/ROM my application...
Hi,
HW:customized nRF52840 board
SW: nRF5_SDK_15.2.0_9412b96
Application: modified blinky_rtc_freertos example (PWM led + freeRTOS task)
Q1) How to verify my application...
Hi,
I am try to try an IMU sensor (mpu60x0) via GPIO but it's giving me 0.6 Volts at output. I have configured the GPIO for High Drive (GPIO_PIN_CNF_DRIVE_H0H1)
Also I...
I am using the latest SDK 15.2
I am trying to build a network of "nodes" these nodes both scan and advertise and will connect with each other.
i currently have 7 NRF dev...
I had some trouble using Visual GDB, it seems their board support packages for nordic are not well updated. I really wanted to use VS studio for this project so I can organize...
I find that nrf5SDKforMeshv300src does not contain some documents, such as how_to_build_cmake.md, how_to_build_cmake_generating.md, how_to_build_cmake_generating_customization...
I have a project that generally operates as a typical peripheral, but occassionally sends advertising packets of type BLE_GAP_ADV_TYPE_NONCONNECTABLE_NONSCANNABLE_UNDIRECTED...
Hello Nordic Experts,
I am developing the pairing in a central. I am working on nRF52840 DK with nRF5_SDK_15.2.0_9412b96 as the cnetral and I have an iOS app as the peripheral...
We are using the nRF52832 with S332 v2.0 of the stack. We have recently been testing concurrent operation of a BLE peripheral connection and an ANT bidirectional master. The...
Hi all,
I'm using nRF52840 Development Kit and Nordic SDK v15.2.0 with soft device v6.1.0
I'm using ECDSA Cryptographic libraries for a BLE related project. I want to...
