I want to change data bytes in the advertisement packet. In ACI_DEVICE_STANDBY I put: lib_aci_open_adv_pipe(1);
In ACI_EVT_CMD_RSP: I get feedback that command 1B (I assume...
first,PCA10005 can't load sofeware hex that after s110 7.0.0 hex(include 7.0.0),and gostudio note that the given hex file can not open successfully.
second,the PCA10005...
Hello! I'm using sdk8 and s110. I want my peripheral device to send data to the central. I doing following steps:
1. initialize service:
void services_init(void)
{...
I am glad that I have successfully used the library from www.libstock.com/.../nordic-semi-nrf24l01-example in a pair of PIC18F45k50 devices. One is acting as a Tx and another...
Hello.
I have had a search but can not find anything so sorry if this has been covered before.
Our company has developed a consumer product using the nRF51822-QFAA-R7...
Hello, I find these structs:
ble_gatts_attr_md_t
ble_gatts_char_md_t
show up quite often in example projects. My qeustions are:
What are these? And when will I be...
I am using esb dpl in nrf5 sdk v11. I want to put a special packet in ack payload. but I think nrf_esb.c code can not do. the reason is that when on_radio_disabled_rx() is...
Hi,
I am developing a printed circuit board for myself using a NRF52 and I am unsure how to actually burn a bootloader program to the NRF52. Additionally, once the bootloader...
Hi All,
my device wakeup from system off casued from reset RWOFF, I read the register RESETSRC and byte E is 1.
maybe there is something about the configuration of gpio...
Hello,
I was reading about that 6LowPAN is being used in the IoT SDK.
I have a few questions about this.
Can the 6LoWPAN node communicate with another 6LoWPAN node...
Hi,
I am working nRF51822 communication. I am using nRF peripherals examples in SDK 11.0 series.
I would like to know the sleep mode examples in communication like after...
Hello,
I bought few nRF24L01+ modules and I integrated them in some custom PCBs that I designed.
I haven't been able to transmit information:
The TX FIFO is full...
I'm working on a very simple Gazell build - basically the gzll_ack_payload example with some of it pulled out, since I'm working on a board with no LEDs or buttons to run...
Hi,
I am trying to develop a PCB for the NRF52 that will use bluetooth capability. However, I was wondering if there were smaller antenna's that could be used rather than...
If I have Bluetooth earbuds, one set to master and the other a slave on my ears.
Is the communication between the ears, through the head, or around the head (Hair scalp...
Hi all
I have two questions/problems regarding the emulated System OFF mode with the NRF52832 and the SoftDevice S132 V2.0.1:
According to this thread , an infinite...
It is to my understanding that you DO have to worry about that when using keil download function or other means to program either the softdevice or your program to the nrf514xx...
hi,
I have created shared channel. currently I only have one master and one slave working.
Master is sending data to slave and it s working perfectly.
But I can not...
Hello,
i haven't found an answer to this question. Which address uses the PTX in Enhanced Shock Burst Protocol (nrf52832, SDK 11)? In the code I found only that:
NRF_RADIO...
Hi
According to the BT spec v4.2, Volume 6, section 4.5:-
"There shall be only one connection between two LE device addresses.
An initiator shall not send a connection...
