This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
I use SDK 9 and nrF51 in the advertising mode. I want to advertise each 1s packets.
First, I call function
set_adv_params(&m_adv_params);
where I
static void set_adv_params...
Hello,
I try to implement the BLE / Cycling Speed and Cadence Service and try to figure out, how to initialize the ble_cscs_init_t data structure. Currently I'm wonder how...
I am building a cadence sensor form the Cycling Speed and Cadence Service module.
Unfortunately the sensor I have built is recognized to have both speed and cadence when...
hi
i flashed s110 softdevice 7.1.0 then ble_app_beacon example application fron sdk 7.1.0 into nrf51822 beacon successfully.but led is not at all blinking in beacon.and i...
Hi
I have got two nRF52840-pdk for long range application design. After reading posts here I realized that the softdevice s140 can only change PHY to CODED after a connection...
Hii guys I am using an nrf51 DK board for my project and I am trying to find the number of advertisements send from the time the board was power up or reset. From my knowledge...
Hi,
I would like to be able to provide a visual indicator such as a blinking LED when the chip is in the Emulated System OFF mode. Note that if the chip is in DEBUG mode...
hi
i tried ble_app_uart from sdk 8.0.0 in pca10028 and it is working.but i want to run it in pca20006.i changed device to 51822 & board to pca20006(in preprocessor settings...
Hi. I'm using nRF52832, SDK13, S312v4 as peripheral.
I want to change connection parameter as below.
#define MIN_CONN_INTERVAL_FAST MSEC_TO_UNITS(30, UNIT_1_25_MS)
...
Where can I find the completed source code for the BLE Services, a beginner's tutorial
I keep having trouble advertising, so either I am missing something, or have incorrect...
Hello,
I used latest port_cmsis_systick.c from SDK13.0. And there is still xTickCount bug. Function vPortSuppressTicksAndSleep() adds correct vTaskStepTick(diff); but the...
I am using nRF52 S132 and latest SDK V11. I defined a custom service with a custom characteristic which is 509 bytes (based on your tutorial). Read operation is fine from...
when a particular line of my code is at line 54, the following compile error occurs:
error: #101: "assert_line_54" has already been declared in the current scope
line...
