At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hi ,
According to nRF51822 Product Specification, running code from flash draws about 4.1mA and running it from RAM draws 2.4mA. But when I tested my code it draws more...
I think the time of uartput is too long (beacuse of the packet recived is too long ,but i can not change it),and when the BLE_GATTC_EVT_HVX comeing ,the uartput is not over...
Hello all,
when using the android version of nRF Toolbox app i am unable to perform a successfull dfu when the application firmware file size is greater than about 60KB...
(mp3 or wav file) --> sd_card --> nrf51822 --> smart phone
Read the data from the SD_CARD transfers to smartphone.
void BLE_SEND_VOICE(void)
{
f_mount(0,&fs);
...
I've not worked with BT4.0/4.1 before, so I was wondering about this:
Take the heart rate monitor example, connection happens automatically when a heart rate monitor is discovered...
I want to change data bytes in the advertisement packet. In ACI_DEVICE_STANDBY I put: lib_aci_open_adv_pipe(1);
In ACI_EVT_CMD_RSP: I get feedback that command 1B (I assume...
I'm interested in using the chip and a very simple board. No buttons, no humidity or motion sensors, just the beacon (like a heartbeat). I'm trying to keep the price down...
Hi all,
I am using the experimental_ble_app_multiactivity_beacon example with S110 v7.1 and SDK 7.2. In particular the hrs_scanner app on the pca10028 board.
I am using...
Hi, I would just like to know if there's an equivalent to "BLE_GAP_EVT_CONNECTED" for services discovered. There's some stored data I want to send in a loop only after services...
Hi,
Does the nRF51822 have a capability of responding to multiple phones?
I am working with RFduino using the RFD22301. I'm assuming that the RFD22301 is the same BLE...
Hey,
the nRFgo Studio contains a simulator for the nRF8001 and 8002. Will there be an update in the near future to simulate the bahaviour of the nRF51 platform?
Mar...
I have TIMER2 running at 500us interval. ANT is working as 100Hz master.
Understood softdevice will affect the timing and cause some latency.
I am guessing it is delaying...
Hi:
I'm implementing an controller for an open source drone Crazyflie ( www.bitcraze.se/.../) . My device is similar to pca10001 board.
Since Crazyflie is acting as peripheral...
Hi all!
I've been unsuccessfully trying to DFU the Smart Beacon Kit with the latest firmware.
Using the nRF51 DK and the TC2030 tag connect cable I was able to program...
