Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
When I enable and disable UARTE RX my chip consumes nearly 500 uA.
I assume the most of it comes from the "disabled" UARTE RX. Either im not disabling it correctly or thats...
Hello,
When we are trying to create mesh using IOS application latest version(3.2.0) but Mesh doesn't work properly.
But the same system is tested with Android Nrf App...
Hi
I am going through the AWS IoT example using an nRF9160 DK, but having some problems with it.
My setup
nRF9160 DK + LTE-M SIM card
I used this same board and...
Hi,
We are working on adding T-M to our middleware, and we discovered a pretty annoying side effect.
We are using NCS 2.0.0
One of our device is controlled using the...
Hi
According to Case ID: 279868 it seems like there has been some issues with modem lock up on nRF9160.
Some questions:
Do you know if this issue is still valid...
Hi there,
I am developing a central in nrf52840 dk using SDK v2.0.0 in VS code.
The BLE part is OK and it is possible me to get notifications.
Now, I need to store the...
Hi,
I have nrf52840-Dongle and nrf52833DK and it was working all good few days back with my code for BLE-UART (Centeral-nrf52840 Dongle and peripheral nrf52833DK) but now...
I need a crystal capacitor for this two Crystal XRCGB32M000F1H01R0 and SC20S-12.5PF20PPM. The value of this capacitor is 12pf and package 0402 So, please help for selection...
I am using a rotary encoder with nrf52840dk and I am confused about how to run sample QDEC code from zephyr/sample/sensor/qdec on nrf52840dk.
I got this error when i tried...
Hi Nordic Team,
Thank you for your support.
One of our customers got Version 2.1.0 for two.
But it was confused. Box label is 2.1.0. But board was 2.0.0 and both...
Hi there,
I have an smart product that will use both BLE & 2.4G Radio. There are few question about framework.
1. I saw radio packet contains such as S0 S1 ADDRESS etc...
I have noticed that the function sd_rpc_open(...) of pc-ble-driver takes more than 1.5 seconds.
I have tried an example heart_rate_monitor which is supplied with pc-ble...
Hello,
I am using nRF52840 DK, and SDK version 17.1.0.
I want to dynamically control CLOCK source.
I tried to release( STOP ) HFCLK( XTAL ) source using nrf_drv_clock_hfclk_release...
Hi there
When the EVENTS_DEVMATCH is raised, this signals that the device address received in the radio data packet matches one of all enabled addresses in the BASE0/BASE1...
