Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
Hello.
I'm using nrf52832 (S132 v7.0.1, SDK v17.0.0) to develop peripheral roles.
Setting UUIDs for advertisements, services, and characteristics. At that time, sd_ble_uuid_vs_add...
Hello.
I am developing using nrf52832 (S132 v7.0.1, SDK v16.0.0) as central and Android device (Bluetooth 4.2) as advertise. Android devices use nRF Connect.
I can set...
We are aiming at a low pin count interface between modules. Ideally we would like to use the programming pins for both programming and as an I2C interface. Is this possible...
Hello,
I am new to Nordic, Zephyr and Linux. I have been going through the "getting started guide" on the zephyr docs website and ran into this problem not being able to...
I heard that nrf52832 rev3 has been released. Our product is using nrf52832 rev2, nrf SDK 15.3. If we change the chip to rev3, can we use the firmware without modification...
Using windows 10 OS, and SES v5.40.
I am using nRF52833 device in my project along with nRF5_SDK_for_Thread_and Zigbee_v4.1.0_32ce5f8 SDK.
As we can see that there is...
Hi,
I am trying out the smp server example with mcuboot and encounter this error when building for the nrf52840 dongle.
I read that it has something to do with the usb...
1. Erratum #7 counsels to add a DSB if reading sequentially from UICR and program flash, as below. But what constitues sequential? If my program reads from UICR on a thread...
I have a BLE application I'm writing using SDK17.0.2, and want to use FDS for some persistent storage. The first thing I want to do is to allow the user to update the name...
Hi,
I am using nCS v1.8.0 for application development on nRF Connect extension of vscode.
But I am unable to configure any unit testing framework to test my applications...
Hi, I am developing a logger for which I am using a memory. I was doing all this using SPI in nRF52832 DK which works perfectly fine. But the problem arises when I am trying...
I have a module using a Nordic chip labelled "N51822QFAAH01621UT". I know it's the NRF51822-QFAA, but I am not sure which model exactly?
Looking on DigiKey these are the...
This is more of a question than a problem:
I have been studying the ble_app_uart_c code and noticed that although data is transmitted to the handler one byte at a time,...
Hello.
We are looking for a viable solution on how to transfer a firmware over the BLE OTA from Particle Tracker (Gateway), or any other mcu to nRF52840 devkit (Client)...
Dear, I am new to Nordic. I trying to understand the various Defines for nRF5340DK kit using Devicetree.dts file. In that, I had look on SW0 defines.
1. The gpio0 reg is...
