After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I use SDK16 and softdevice S140. I use cdc_acm to simulate a UART port. My data traffic is very heavy. It cause data overwrite and send out many zero. My source code snippet...
Hi,
I have been trying to use nordic nrf52840 USB dongle/ pca 10059 in BLE mode to fetch data published through Bluetooth; however I can find any compilers that support...
I have adapted the example ble_app_gattsin SDK_17. My code is as follows:
However, an error is thrown when setting the scan filter as follows: nrf_ble_scan_filter_set...
Using app_usbd_cdc_acm_write method as blow: I see following output in Putty.
Baudrate is correct (115200) + it decodes first part of the message.
I have no idea why...
When I try to program custom NRF52 board using a J-Link v9 (It's probably a copy product), I'm getting the error below. I also have several NRF52/NRF53 DK boards when I try...
More than once I have started to develop a module based on an SDK example project only to find out that it uses deprecated code and drivers, so then I have to update my code...
Good morning,
I'm developing an application for nRF52805 using NRF5 SDK.
I have successfully integrated FreeRTOS into the example application.
I would like to add CMSIS...
Hi,
I have a question about the behavior of the Softdevice S132_nrf52_7.0.1 for the nRF52832 in case of the reception of an advertisement packet of type ADV_NONCONN_IND...
Hi all,
Would like to know that is there anything that is similar to TrustZone, which the key is not hardcoded in the application program, installing the key file like...
Hi we currently have a product develeped for 52840 on basis of old sdk 15.3. We are just about to start a new development based on 5340 for which we are required (and want...
Hi Experts,
Recently, I am developing the mesh project based on the latest nRF mesh SDK, everything is running well. But I encountered one issue, that is how can provisioner...
Hi,
I've followed the instruction from " Developing for the nRF52805 with nRF5 SDK" to port the example "blinky_freertos" but I got the following compilation error:
This...
Hi.
I have 3 Dev Board's MBN52832DK and Ill like like to upload the BT Mesh example into those boards and I'm not very expert on this topic, dis you have any Webminar or...
Hello,
i was wondering about the stated antenna efficiency here:
infocenter.nordicsemi.com/index.jsp
The very poor values (< 20%) provided for the efficiency do not...
Hi,
I have experience with the ESP 16/32, pi zero and BOSH XDK. I have been working on some IOT mesh stuff and I have a good product idea that I know I can build with your...
