After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a 9160 DK board with lte_ble_gateway on the 9160 side and hci_lpuart on the 52840 side. It works as far as being able to send and receive BLE messages but it has faults...
Hello,
Previous revisions of the nRF SoC's such as nRF52840 and nRF52832 have had specifications for certain IO to be low frequency < 10Khz and standard drive only because...
Hello
I'm facing an issue with app_timer_start. Indeed, with small values, sometimes, the app_timer_start won't start the timer. As a result, the interrupt handler is not...
Online Manlio 6 minutes ago
Hi,
I add NFC to my project with freertos. The initialization of nfc is ok. After running few seconds ,it hang. If I comment the usr_nfc_init...
Hello,
I work with the ATE using Algocraft WN series programmer.
It has directly access to GPIO registers through SWD interface with WRITE / READ / COMPARE commands. ...
Hi,
I was tracking down a bug that resulted in a secure fault exception. To save some time tracking it down I enabled logging in the spm. However this resulted in an escalated...
Hello,
So I am just real confused on how the softdevice programming works via the open_bootloader right now and can't seem to track down the documentation I need to be successful...
I'm running a code based on the ble_app_uart example using the PCA10059 dongle. I have the dongle connecting to a raspberry pi 0 W via BLE and when this runs using a power...
Hello,
at the moment I am working on a project with a nRF52840DK as central and multiple nRF52DKs as peripherals. The code on the central is based on the "ble_app_uart_c...
Do the examples in the SDK folder like ble_nus have their binaries with softdevice already? I'm a newbie in Nordic and using the BLE NUS example with nRF52-DK to learn as...
Hi team,
My customer wants to develop a system with one central, multiple peripherals, each bandwidth is <50kbps, but they want the latency can be as small as possible....
Hello,
I would like to know how can i use SPI on the radio example.
I'm using (programming) the radio example, receiver, for AoA and it's working so far. What i'm trying...
Hi,
My observations: DSP_PRESENT Macro is enabled in nrf51.h , nrf52.h, nrf5340_application.h files in v1.5.0\modules\hal\nordic\nrfx\mdk path As shown below: #define...
Hi
We are using nRF52832 with SDK17.2 and SD 112.
We are trying to make a NFC_PAIRING_MODE_GENERIC_OOB to a PC with the following System Information:
OS: Windows 10...
Dear All, I have noticed the following issue: In the beginning of my code execution pin 1.09 is high, before I can even call . From what I found in the datasheet pin p1.09...
