Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
Hello,
I wanted to know why StackLimit is not defined using HeapLimit in nrf52_common.ld ?
Given the fact that the HardFault handler ( HardFault_Handler ) is checking...
What are the MIPs of nRF52832 with S132 softdevice enabled? Also, changing the softdevice to S332 will affect the MIPs? Regarding S132 and S332 softdevices, they are all same...
I have a custom PCBA running my development firmware. When I turn everything off (meaning no peripherals are active - most chips are in sleep mode or de-powered; BLE disconnected...
Hi
Can I use app_timer with APP_TIMER_CONFIG_USE_SCHEDULER set to 1 when using task manager?
Setting APP_TIMER_CONFIG_USE_SCHEDULER to 0 causes the timer to fire, but...
Hi,
I am using SDK 15.3.0 for nRF52840.
We don't want to use peer manager and id manager as we don't need bonding.
We added the remote device with public address type...
nrf52832 SDK14.2 s132_nrf52_5.0.0_softdevice PCA10040 ble_app_hids_keyboard
I m odify the proj ect :
two service : one is hid another is different hid_1
press button...
Hi!
I have been trying to observe the NRF_LOG_xxx output in my Eclipse console on debugging mode. However, nothing prints in the console (image 1).
I tried enabling...
Hi
Befor I used nRF51822 to transmit a packet per 5ms, payload length is 12. I can received 200 packets/s, Initialization settings are as follows
Device : nRF51822...
Dear all,
I have been struggling with updating my advertisement data package in SDK15. Using Jimmy Wongs's example ( https://github.com/jimmywong2003/nrf5-modify-device...
Hi,
to initialize the button properly
to trigger the push event on button push and the release event on button release, do I just have to change the button active state...
Hi there,
So I am trying to get a basic mesh setup between multiple Nordic Thingy 52's and no matter what I have tried i keep failing,
I have gone through the forums...
I have an Adafruit Bluefruit Feather nRF53832 board I am considering using and need to change the default serial baudrate from 115200 to 9600.
I am told that I can use the...
Hi:
I am using a shake sensor as an analog input wake-up system. The system is not system off. The analog input signal only generates an event to wake up turn on...
I am using the UART central, integrated with peer manager and UART peripheral application from the SDK 15.3 on our custom hardware. I have 2 centrals running exactly same...
Hello everyone.
I want to familiarize with The Power Profiler Kit. I've installed proper software and been trying to connect to the device but every time I receive the same...
