This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to write my ADC samples over spi on a sd card (Using SAADC like in the sdk 12 example with PPI and using fatfs like in the example in the sdk).
I open...
I have been using the pc-ble-driver Python bindings to implement a peripheral. I have extended BLEDriver to support sd_ble_gatts_* the functions. I now have a working peripheral...
Hi All,
I am struggling with this question from many days. Does the SPI transmit or receive operation in SPI master code uses DMA? While using SAADC DMA I have specified...
I'm using an app timer to blink an LED while in the bootloader.
Initially I was configuring an app timer when the bootloader started up and never stopped it, assuming the...
After failing in replacing a Cortex M4 for a NRF52832 I'm studying the possibility of using a NRF51822 as a BLE controller, used by my Cortex M4 MCU.
As I saw there is...
Hello
Please tell me about sd_ble_gatts_value_get ().
Before execution, handle is 0x11, but after execution it will be 0x00.
Is this an abnormal thing?
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
main.c
something
hello there i want to scan perticular device. can any one helo me?? . i am using heart rate sdk 11 example
static void on_ble_evt(ble_evt_t * p_ble_evt...
Hello dear Nordic team,
we want to implement a white list to our central device in the production process. Bonding while producing is not an option for us.
Therefore...
We are having a project where temperature values will update whenever the temperature changes ,So I'm writing code like this
uint32_t ble_sh35_update_temp(ble_sh35_t *p_sh35...
I need to generate DFU init files on my Mac for OTA firmware on the nRF51. I haven't found a solution for a Mac-only environment (i.e. no Master Control Panel). I spoke to...
Hello,
I am looking for a SPI library which is simple enough to send and receive a byte from sensor. Something like this. for nRF51
spiwrite(ADDRESS, BYTEtoSEND);
val...
I am using PCA10040 evaluation board to test I2C connection.
I tried twi_scanner sample code in SDK 12.
I wired SCL and SDA pins to D0 and D1 to a PicoScope device....
Hi,
I am now trying to add DFU functionality to Proximity sample application.
The SDK I use is nRF5 SDK v.11, and the board is pca10040.
I have tried to add DFU to...
I am using nRF5_SDK_12.2.0, S132-SD-v3, nrf52832 pca10040 board, ble_app_uart
When measuring current consumption using ble_app_uart -> 0.6~0.8mA(advertising)
I want to reduce...
