Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
I am trying to set up a project that uses MCUBoot and puts the secondary slot into QSPI External Flash. I'm using NCS 1.7.1 with VS Code. I've followed numerous posts on these...
I am currently evaluating the differences between nRF52811 and nRF52810. I am still using the nRF5 SDK.
One difference is in the nRFInitialize function in the startup code...
Hello,
In my application (using sdk 16.0.0) I have a bootloader that allows to upload a new firmware through either BLE or UART. The Bootloader is initialized as usual:...
Hi All!
I have a problem running simple PWM output on NRF5340 board. I have a following code:
Now what i'm trying to achieve is to get 50% of duty cycle with frequency...
Hi there,
This should be straight forward but has me stumped. I'm trying to add BLE to my CAF based application and can't do and recreated the same problem with the samples...
Hello, I have a two part question with regard to SPIS setup time when exiting low power mode on an nRF52840.
We are using the SPIS peripheral on an nRF52840. General guidance...
Hello,
I am currently integrating the Wiznet5500 drivers into a VSCode project, but I am stuck on where to include these custom modules.
In the previous version in SES...
Hi，
I have a problem about CAF leds modules. I submit a led event to turn on led for 3600ms and turn off led for 500ms, but it work inversely in fact.
I find that leds...
SD140
Part nrf52833
Application: Central App that connects to 1 to 16 different peripherals. One at a time.
Problem: 1/10th of the time, I get a disconnect reason BLE_HCI_CONN_FAILED_TO_BE_ESTABLISHED...
I keep getting a hard fault when calling spm_request_random_number()
I'm following the secure_services sample provided in the SDK, and the secure_services header file...
Hi, I am using the nrf52 Thread v4.1.0 SDK for development
I am using ADA4333
there pin 6 is used for Gate control but
in CLI pin 6 is used as uart tx
and it is hard...
I found the following problem with Programmer v2.0.1, using either a Nordic DK or a Segger J-Trace as the programming device (on Mac OS 11.6, and with nRF Connect 3.9.1):...
Dear All, I am trying to add the task watchdog to my application, but I am dealing with some interesting issues. The NRF SDK that I am using is the v1.6.1 I have dealt with...
Hey,
I saw the example in the SDK for hid keyboard over ble but it is only as a peripheral device.
In my project I have the nordic board as a central device connecting...
It has an iso_broadcast error, by GDB, it is in function ` bt_le_scan_start() ` where it throws an error. The error I cannot see through since the compiler option can't adjust...
