Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hello, I am having an Assertion failure like this:
My nrf/ext/lib/bin/supl/CMakeLists.txt looks like this:
Line 9 is already changed to if(CONFIG_FPU), as per the...
What is the default data rate of Nordic BLE, and when is it set in the Thingy code? I can't find any reference in the code to what I assume would be NRF_RADIO->MODE!
Why ram and flash size in a board configuration in Zephyr OS for nRF5340PDK doesn't match with declared on your site? According to your product specification, application...
nRF52840DK devicetree describes both uart0 and uart1 explicitly in nrf52840dk_nrf52840.dts file: https://github.com/nrfconnect/sdk-zephyr/blob/v2.3.0-rc1-ncs1/boards/arm/nrf52840dk_nrf52840...
Hello,
NRF52832 - SDK16 - sd132 7.0.1
I have an issue with ble_db_discovery_start() that return NRF_ERROR_NO_MEM, when I followed the functions call I found the error...
Hi,
I started with the Blinky example and have added peer_manager to the project by referencing the hrs example. Everything is building, but on init() I am getting a hard...
I have two custom pcbs containing the nrf52832 chip with the EXACT same hardware and software.
When I program and run the old pcb,
The old pcb runs OK. It returns from...
I use SDK 15.3 and SD S340 v 6.1.1. Bootloader is designed to do custom update through GSM; code based on secure bootloader ble example from SDK. I have used code that previously...
Hi,
Greetings!
We are using following setup
nRF52832 DK
SDK16.0.0
Mesh SDK 4.0.0
Light Switch Server and Client
Here we would like to understand below things...
HI,
I set RTS,CTS to disconnect in the overlay file.
(Toolchain Manager.0.6.1/NCS1.3.0)
&uart0 { rts-pin = <0xFFFFFFFF>; cts-pin = <0xFFFFFFFF>;
};
warnings occur...
Below are the details of my setup configuration:
SDK Version: 11.0.0 (with changes corresponding to hardware)
Soft-device: s130_nrf51_2.0.0
Boot-loader: nrf51422_xxac_s130...
Hi, I am Working on nRF52840 and using nRF52840-DK.
Below is my working environment SDK - nRF5_SDK_16.0.0_98a08e2 ,
IDE - Segger Embedded studio (windows 10 - 64 Bit)...
Hello! I gonna buy a NRF52-DK. The seller says the following about kit version :" Hello, original imported. The latest version of 2020. 2.1.0 version". Is it correct? I can...
Hi
In my application, I use nrf52811 to relay data to make the data go further. If data is sent from point A to point B, point B receives the data and then forwards to...
