i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Using NRF_SDH_BLE_OBSERVER in a non-static context doesn't work because the registered variable, and therefore the handler context is lost. How can one register for ble events...
Dear,
I am using nrf9160 DK, we can download hex fiel for boardcontroller
nRF9160 DK board controller firmware
https://www.nordicsemi.com/Software-and-Tools/Development...
Based on the experimental_lpn example if have ported at application (light switch) to work as a low power node.
Everything work fine on the lpn node where i use the generic_onoff_client...
Hello,
I tried to update bootloader on the dongle via DFU, but It failed.
The dongle uses OpenBootloader, so it does not check signature for firmware packages. But the...
Hello,
I'm working on a project where we are doing the following:
Collecting sensor data and storing it in an external SPI flash
Retrieving that sensor data from the...
Hi,
When publishing a message with access_model_publish() the p_message->p_buffer must be remain valid until all retransmissions have completed for loopback message but...
Hello
I want to modify the tx powel level to 4 dbm using sd_ble_gap_tx_power_set(BLE_GAP_TX_POWER_ROLE_ADV, m_adv_handle, 4); after Advertising_Init function.
I could...
Testing with the NRF52840 dongle and the Power Profiler Kit. I see a reading of ~5uA when sleeping without SAADC enabled.
I use this code to enable SAADC
My power...
Environment
- DK 0.8.2 in which SB44 is cut, and P1 and P2 are connected - firmware v1.0.0 - program : asset_tracker - SIM: iBasis
Before updating firmware, asset_tracker...
Hello. Got such a problem. I use nrf52832 Adafruit Feather board. While working with BLE examples (Softdevice and app.), debug via serial works fine. Can see all the text...
Hi,
I have a desig where the space is minimal and I have one nRF52838 and one nRF52840 microcontroller. Is it possible to place them at the same coorinates, but on oposite...
Hello everyone and Good day
I am a fresh graduate and its my first assignment at my job. I have to flash an LED at 1 Hz using NRF52810 BT 5 chip.
There are so many development...
Hi,
I am using nrf51422 interfacing with Ti's CC256MODA Bluetooth so here can you plz tell me how to do pairing with the TI's bluetooth .How to give passcode to the device...
