Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hello I'm using the official example and BLED112 dongle with the demo from C:/Bluegiga/ble-1.60-140/src/thermometer-demo (main.c in attachment). The problem is that device...
I'm using SDKv15.2.0
I think there is a problem in nrf_dfu_app_is_valid() in components/libraries/bootloader/dfu/nrf_dfu_utils.c
If the CRC check fails, the return value...
Hi,
What is the timing of the indication retry mechanism (SDK14.2, nRF52832) ?
App use sd_ble_gatts_hvx() to schedule message for sending
At the next connection interval...
Hi, Great Nordic Support teams:
I'm wondering if the only limitation of the choice of L3 on nrf52832 layout is just the tolerance under 10%?
Cause it seems to be the...
Hi,
I've recently enabled the watchdog in our project which included buttonless DFU. Project is based on FreeRTOS, SDK14.0, S132 v5.0.0 on custom board nRF52.
Since the...
Hi All,
I'm running a windows box with Android studio with the GitHub Thingy Repo https://github.com/NordicSemiconductor/Android-Nordic-Thingy project downloaded. The project...
Hi Nordic,
I am using SDK 12.3.0, S130 2.0.1 and PCA10028 nrf51 DK.
I would like to ask about SPIS and SPIS event "NRF_DRV_SPIS_XFER_DONE".
1. What would trigger event...
HI,
In need to generate a sweeping tone to drive a piezzo element, i determined the tone should be sweeping back and forth between 2.5KHz and 4.5KHZ at an approximative...
My ultimate issue is trying to get a bootloader working on custom hardware with an nRF52832. The bootloader is mostly the base UART DFU bootloader from the Nordic SDK, with...
Hi,
I'm able to run the DFU mesh from the quick guide and now I want to integrate the DFU into my application.
My application is based on the light switch example, so...
Please help me fix my computer to allow nrfStudio to program pca10056.
I just received 2 pca10056 1.0.0 2018.35.
I am on 2 computers A and B: both with windows 10 64bit...
I trying to debug an interaction between using SPIM3 on the nRF52840 and the BLE stack in the SoftDevice . A reset is happening, which I think is being generated by the SoftDevice...
Hi I have an application where ESB will be used in the same environment as a few BLE devices which are also our devices. My plan is to set an rf_channel for ESB and then at...
We have an application where we have a large number of sensors, some relay nodes and one or more gateways. The sensors and relay nodes are provisioned by the gateways and...
