But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
I have found these 2 threads in this forum regarding this matter but I am a bit stuck.
devzone.nordicsemi.com/.../
devzone.nordicsemi.com/.../
I want to port the...
It's been 14 months since the nRF 5x IoT SDK 0.9 was released.
Given Nordic's normal release cycle, that's an eternity!
Will there be another release or is it dead now...
Hello community,
Before I was using a pca10040 by Nordic evaluation board. The project, that i developed, is running well using the EB but when I change to sparkfun breakout...
Hello,
I'm working on nrf51822 with SDK9.0. I have two modules, one is working as a peripheral using s110 and another one is as a central using s130. Now central has a very...
Hi!
I am fairly new to programming micro controllers so apologies if I ask many questions.
I am using NRF52832. The situation is this - I have 2 devices and 1 host . After...
Hi all,
I've found the nRF52840 with USB but it seems a bit OTT for our application, something more like the 51822 would be nice, but cannot identify one, can anyone list...
Hello!
I have a code that is working perfectly on Eclipse for Linux and I would like to copy it to a windows computer with keil. I created a new project with Keil copying...
Hi, I'm developping endless PWM sequence.
That is ...
Only one output pin and the signal from it is repeated with the same period of pulse but with two different duty...
Greetings,
I'm having some trouble using the secure DFU bootloader and buttonless DFU service in my application. The code for both of these has been taken from their respective...
nRF52 SDK13 S132.
For example, I have handle from 0x180A service.
I want to read characteristic 0x2A24 from here.
How should do it?
In the watch window I can see event...
We are interfacing to a SPI Flash MX25R8035F.
When attempting to read 1 page of 256 bytes from the chip we break the read command up into 4 SPI Commands.
1) Read the Status...
Hi,
I`ve made fixes in SDK 13.0.0 files described below:
nrf_section.h : to supress gcc warning: invalid suffix on literal; C++11 requires a space between literal and...
When I set the PWM driver for very low frequency i can see how it blinks, the thing is that it always blinks where it's more or less 70% of the time ON and 30% OFF .
When...
Hello,
Working on a project using the pairing and bonding security model, I would like to filter out of a central's scan all already bonded peripheral devices. Or, I could...
