But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello !
I am trying to read WHO_AM_I register from a LSM9DS1 IMU.
I have spi_update_imu_data() as my callback for when the spi transfer completes and inside it I make spi_xfer_done...
Hi all,
Using nRF51422 on nRF51-DK as a Central I have been successfully connected to a non-Nordic BLE peripheral, however when using the ISP130301 chip that embedding...
nRFgo Studio will not install.
It is rolling back when it is in the proocessing of copying.
The net framework4.5 has been installed on win10, and the virus softwares have...
I have recently purchased a few nrf51822 beacons. I have been successful in detecting the beacons on the Android and iOS apps. The firmware documentation says I need to press...
I just got an 32u4 BlueFruit LE board. and want to create a customized FW for its nRF51822 v3 chip.
I am using STLink v2 and OpenOCD connected to this chip. To verified...
Hello everyone! Frist of all, sorry for my broken English.
I had a timeout handler, which call by application timer every 50ms. In this function I took data from accelerometer...
I have a few nRF51-DK's lying around. I've compiled this simple test program using Yotta/mBed.
#include <mbed-drivers/mbed.h>
Serial pc(USBTX, USBRX);
DigitalOut...
hello,, i want an additional information on this product.... End of life of this chip... how long the chip will be available in market. Because we in our company decided to...
Hi,
I use the nrf24le1 device in my design. I want to stroe data when power is off, so I write data to the NVM flash. But something is wrong in my design, could you help...
Hello,
I am using the nRF51 transmitter_pca10028 example to try to communicate with legacy systems using nRF2401A.
I could achieve nRF51 TX to nRF24 RX successfully...
I would like to burst out 12 packets of 64 bytes and then go into RX mode immediately after for a single payload, followed by another round of transmissions. Is there a shortcut...
The data is sampled at 3khz, each sample is 2 bytes, connection interval is 7.5ms ,4packets per connection interval. The data is displayed on a graph with respect to time...
When I execute nRF5x_MDK_8_7_1_IAR.msi from the SDK 11 directory the files from the .msi are added to the IAR install directory, not the SDK. These changes are ignored when...
I was little bit confused between NRF24l01 and (+) plus version which is better . i want range of 900-1000m. which is best??
If i choose NRF24l01+ what are the ways to...
(/attachment/0495424521df76d5b8f8e66c969ed791)Hi,
I add ANCS Service into my Heart rate ref ble_app_ancs_c example code.
I use MCU nRF51 and SD130 in nRF5_SDK_11.0.0_89a8197...
