After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
Hello I am working with the nrf54l15 soc (sdk 2.8.0).
I have noticed that a component "mx25r6435f" is defined in the generic nrf54l15_cpuapp_common.dtsi file.
With some...
Hi,
I am currently using nRF54L15DK for Channel sounding development.
however, I would also like to add direction finding function, I know that there is no direction finding...
Hi,
We're a bit troubled by the known issue NCSDK-20567: Partitioning limitation with MCUboot swap move , and are trying to find a work around.
Since the issue is with...
Hello
I am trying to implement AoA reception using the TimeSlotAPI on the nRF54L15.
I have previously implemented a simple AoA reception function on the nRF52833.
Please...
Hi,
I'm trying to set up two nRF5340 Audio boards - one as a unicast client (gateway) and the other as a unicast server (headset). I have seperate config files for both...
Hello, we've been using nRF5 SDK and nRF5 SDK for Mesh for about 5 years now and we're looking to port our codebase to nRF Connect SDK.
We have already started the process...
Dear Customer Support,
Reaching out for help / example on couple peripheral configurations
We are using nRF Connect 2.5.0
1-UART
we have the following configuration...
I am using a Sierra Wireless HL7800 modem with the nrF52840. I have been able to receive SMS messages and see them come through the RTT log. Setting to text mode and then...
Hi,I am using NRF5340 ,I want to log data of 2 channels of mic with sampling rate of 16000 but while logging I am receiving "120 messages dropped" and with some random numbers...
Hi. First of all, I appreciate to all users support. I work with SDK 17.1, nrf52832.
I`m trying to make multi link Central. It connect to multi Bootloaders for DFU.
When...
Hi, I am using the npm1300 with the nrf9160 with ncs2.7 When we do a reading from the npm1300 to get the current and voltage values, the readings are always delayed by 1 reading...
Hi
I was trying to take code from ble template and put it in my own project. Even after copying the entire main file and including file directories it shows loads of errors...
I want to set serial communication over USB and try to implement CDC ACM functions on nrf52840dk-nrf52840.
prj.conf:
.overlay:
But now, build on NCS v2.7.0 stops...
Hello~
I am developing nrf52840 with zephyr ncs tool chain v2.7.0 and SDK v2.6.1.
We had made our own pre-production PCB, and trying to lower down power consumption. ...
