i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Hello Nordic! I have connected a sensor to the DK via SPI. It outputs a lot of data, a lot... for 1 second of data I get 4096 entries. Each entry is 10 bytes in length.
...
I'm working on a design featuring two different MCUs. I'm looking to use the nRF52840 as one of them. I need both processors to be able to send each other messages and ideally...
Hi,
I have a weird problem. My application starts two timers, one after another. Like this:
Normally it just works - no errors, nothing. However, after a DFU OTA upgrade...
What is the best method to store TLS certificates on the nRF5340? I have seen 2 options, but I'm not sure what is best practice and what does work.
If I store the certificate...
Hi,
i just got my hands on Thingy 52, just want to know how do i get started in retrieving data from it, specifically for motion(accelerometer data), if someone can point...
Hi,
I'm trying to interface LR1110 (Dev Board) with NRF9160 DK using SPI. I have been working on this for a couple of weeks, explored almost the whole devzone, learned a...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
HI,
I need to check the following thing with you. I need to use an I2S mic with NRF5340 between the mic and the controller we need to place 2meters of wire. So, I need...
Hello All, I'm currently working on an application with a central and peripheral devices both using nrf52832 with SDK 15.3 and S132. I'd like for the central to be only trying...
Hi Nordic Team,
My dev environment is as follow:
nRF52832(Ble Central + nfc) + S132+ SES
I have integrated BLE Central Multilink uart project with nfc writable ndef...
Hi Devzone,
A couple of conceptual questions about what is possible and a request for ideas for how to best accomplish my goal.
I want to implement a command line...
Hi,
I am working on an application that needs to store data in flash memory and runs on the nrf52840 dongle. The application is running on an operating system with possibly...
Hi guys,
I am trying to flash my nrf52840 dongle (with the Segger j-link mini) via your awesome NRF Connect Extension on my Apple M1, but I can't get it to work inside of...
I was able to work with the spi module, but now I want to make it work like a simulator, so I updated the configuration function and tried it like this.
Could you please...
