We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Dear Sirs, good afternoon
I am using a (PPK + nrf52840 DK) to measure current on an external device.
Is it necessary to cut the SB40/41 jumpers in this case?
Thanks...
Dear Nordic ：
I want FTMP (Fitness Machine Profile) to be supported in my product (A smart trainer uses NRF52832, called Gravat in Ant+ official website).
I find that...
I want to monitor the RTC count and generate an interrupt when a specific count is reached. And without stopping the RTC, I want to generate an interrupt again when the next...
Hi
We have the issue that GPS has no fix.(board: Thingy91 version: 1.0.2) I used the pre-compiled hex thingy91_ltem_dfu_2020-04-29_bc7ade8b.hex downloaded from Nordicsemi...
i want to connect Nordic thingy to a nrf 52840 soc with ble central example.
all i want to get is thingy environment service and get temperature and humidity values on...
Hello,
I got the acceleration value using mpu6050 sensor. And I am going to use this to get the angle of the sensor. The formula below has shown that angles can be obtained...
The application cannot write the app_update.bin on Windows.
How do I write with MCUboot & DFU & application?
[Command I tried]
dfu-util --alt 1 --download .\build_nrf52840dk_nrf52840...
Hi,
I have a similar issue as Wille in his question . I was trying to alter the example "nfc_text_record" for my needs. The code compiles without a problem, but when I try...
Hi,
After setting up my IDE and toolchain and trying out some example codes, I wanted to try the example for NFC pairing from SDK ver 17.0.2, because the pairing via NFC...
Hello,
I have some questions relate to Advertising:and RF ANT:
As I understand about advertising, there are only 3 channels, which can broadcast the advertising, are...
Hi, I'm using nRF52832 Software Development Kit, PCA10040, S132.
I'm trying to follow this example.
I connected successfully, but I have problem in 'Advertising' part...
Hello, Support team:)
I wish to use NRF_LOG_DEBUG function in segger embedded studio.
But there is no message in "Debug Terminal".
- nRF SDK 16, "/examples/proprietary_rf...
Hi
I am now working on a project which I use ble_app_uart_c as a reference.
SDK 16 and used softdevice s140.
UART works normally at 3.3V.
But if I lower the power...
Greetings. I am on a mission to upgrade the BLE Firmware of nRF52840 via UART and ultimately via the UART communication between our main Micro (Microchip PIC) and nrf52840...
