Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
I'm a newbie to nRF stuff so please forgive me if I have missed the obvious...
nRF52840, SDK 17.0.2
The Nordic infocentre lists 4 options - SAADC driver - legacy layer...
Hello,
I am trying to observe communication between the nRF9160 and nRF52840 on v0.8.2 of the nRF9160-DK board. According to the schematic and documents, P0.23 should be...
I am putting data in a queue whenever I get indication, something like this:
on_indication(..,.., received_data)
self . qure_received . put (received_data )
Is there...
Hello
I'm trying to send a dataset from the nRF51-DK over BLE to an iOS device. The total data to be sent is around 500 kB. What is the best method for transmitting this...
Dear Nordic Experts, I've added buttonless BLE DFU to the generic level ( Mesh ) example. The firmware update is basically working; except for two minor little limitations...
SDK: 4.1.0
CHIP: 52840
old question
Hi, I have developed sleepy zed.
I have success to send "request data" in every 5 sec.
I wants to add regular job which is send...
Dear forum and Nordic Support team,
I just want to confirm that there is only one Broadcaster (Advertising) role possible at given time on Nordic Soft Devices (e.g. S132...
I tried the logger examples in the Zephyr that work on the DK but not on the dongle. I tried to change the Kconfig options using Segger to enable the logger but those options...
Dear Mesh Experts. As of 2021, using nRF5_SDK_17.0.2 and nRF5_SDK_for_Mesh_v4.2.0: What's the simplest way to persistently save and load some values in a mesh project?
Google...
Hello
I'm requesting a feature (since I can't find a way to do this?) to read all relevant LTE network parameters from the connected network when using the nRF9160.
When...
We are using powerdown() function to put the procesor in sleep mode for the said time
We are facing following difficulties
1. It does not work if we use nrf_delay_ms(...
Hi there,
I am developing a product using the nRF52833 QFN40 package (nrf52833_qdaa), and have the nRF52833DK for testing which uses aQFN-73 package (nrf52833_qiaa). I am...
Hi,Master:
Question：
When the finished product cannot be debugged with jlink, I want to save and trace the function stack information through the firmware. When there...
Is it possible to merge client and server to one image using ble_uart Example?
Which could work as client ,also as server ,it controlled by program.
Thanks a lot.
Hi,
I'm using the NRF52811.
In my schematic, the SWDCLK and SWDIO is connected to an external connector and the NRF52811 is connected to MCU through the SPI channel...
