Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
I have merged two program SPI slave and ble_app_uart
I am getting these two errors
undefined reference to `nrfx_spis_buffers_set'
undefined reference to `nrfx_spis_init...
Hello,
I'm using nRF52840 dongle. I implemented a virtual COM port to send messages to my computer. My problem is that I can send messages only if I'm already connected...
Hello everyone, I ask for help to install the new version of SES in Ubuntu Linux 18, since the license is not recognized by the em nor the hardware, I can program the card...
After enter low power mode I aim to config to wake up on a 1 sec timer, but in 20 us the event 0x26 comes. I cannot find what event ID 0x26 is and how to disable it ?
Info...
I am having an issue when building the hci rpmsg example for the following youtube tutorial
Zephyr RTOS and Bluetooth LE on the dual-core nRF5340
I've tried figuring this...
Hello,
According to the description in below page, " The image can be an application image, SoftDevice image, bootloader image, or a combined image of bootloader and SoftDevice...
I am trying to interface adxl362 sensor with ANNA-B112 evaluation board.i am trying to read the part id to check the connection. The code is pasted below.
nrf_drv_spi_config_t...
Hi! I am using the 52840-DK dev board.
I want to use two pins, P1.0 and P1.1 as GPIO output pins.
In my code I have;
nrf_gpio_cfg_output(BLE_CONNECTED); nrf_gpio_pin_clear...
Hi everyone,
I want to serial print three float values (x,y,z) from an IMU. I use the MACRO NRF_LOG_ERROR( "Float_Value: " NRF_LOG_FLOAT_MARKER "\r\n", NRF_LOG_FLOAT(value...
Race condition in starting the ADC following calibration. I am trying to start the ADC in the interrupt routine when the end calibration is reported, however I have unreliable...
Hello,
I have two brand new nRF52 DK eval boards version 2.0. On both boards, the reverse charging diode D8 is missing. That diode is required to power the board externally...
Just trying to build Nordic sample codes S110 with nRF51822.
Here is the error. These are hidden file. I guess some configuration is not correct but I'm not sure.
---...
SDK: 15.1 IDE: Keil Softdevice: S132 v6.0 Hello, I am using the ble_app_uart example as a starting point. My goal is to send 5 bytes every 5 seconds to another nRF52 Development...