When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi,
I am using 15.2.0 SDK and 3.0.0 Mesh SDK for development.
On the Nordic nRF Mesh App, we made certain changes to the generic level slider such that it send out live...
Hi, I am using Heartbeat messages with the light switch example, and want to log the nrf_mesh_rx_metadata_t in heartbeat_opcode_handle() to RTT viewer so I can write it to...
Hi,
if my device (nrf52832) is in application and I perform firmware upgrade using nrf connect and PCA10031 on Win 10, the upgrade process is very slow (0.35 kB/s). I stop...
Hello,
I have a following requirements,
Build a custom bootloader which accepts DFU through OTA and UART.
this boot loader must also contain softdevice , so that finally...
I'm having problems with toggling the EXT0 pin on my thingy:52.
I have tried with setting the EXT0 as an output like this: drv_ext_gpio_cfg_output(SX_IOEXT_0); And then...
This is not really a problem - more like an enquiry
Is it possible to gate PWM output using another GPIO pin e.g. if the second pin is low then so its the PWM otherwise...
Hello,
I would like to test and adapt the example "ble_app_uart_coexist" with my nRF52840 DK. Unfortunately, I believe that this one is only intended for nRF52832 and softdevice...
Hello,
I am trying to use the BMD-350 evaluation board to program a standalone BMD-350 module on a custom PCB. I have followed the instructions in the documentation to connect...
Hi,
I'm using custom board with the nrf42840 and I need to use p1.09 as a GPIO.
How can I do this in a debugging mode (using the PCA10056 as a jlink)? Can I get a code...
Hi,
I want to get interrupt on GPIO using gpiote module.
I searched for example but couldn't get it.
Can you guide me how to use gpiote in nRF9160 ?
Regards,
Smitesh...
Using Fanstel BT832A BT 5.0 Module which utilizes SoC nRF52810 QFAA
1) Yes or No: can I configure a GPIO as a Timer/Counter Input so I can feed a high frequency input into...
Hi,
I just wanted to know which flash is used by the flash manager within the SDK Mesh v2.2.0 onoff client/server examples ? Is it the 1MB internal flash or the external...
Hello,
During development of a custom board, based on the BMD-300 module from Rigado, which uses an nRF52832, we ran into a SoftDevice fault under specific circumstances...
Hi,
After trying to work out why one of our nrf9160 DK:s cannot execute any AT commands using the at_client sample I tried redoing the getting started guide to make sure...
