But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
I have 32x64 RGB LED Matrix, and I want to use nrf52 to control it. I got the driver working and I can display everything. It is a time interrupt driven driver, just redraws...
So I just got my nRF52_DK, got everything installed and compiled an uploaded the blinky example. Fine. I had my custom PCB ready, and got the 52832 soldered in straight away...
Hi, I am a newbie to embedded development. I am well versed with java script. I am under the impression nordic allows you to communicate with java script to the development...
Hi, we're using \nRF5_SDK_14.2.0_17b948a\examples\ble_peripheral\ble_app_hids_keyboard to test Pairing/Bonding/whitelist.
After connection, when the central try to read...
Hello,
We have constructed a custom board of nRF52832 via I2C communication with sensor and INT based wake up. Following configuration enable
DCDC Power Enable
Disconnected...
When I was using a master slave integrated host, when I quickly disconnected the connection and then set up the connection immediately, it was found that the original disconnected...
Hello,
is there a simple example for reading out a value? The nRF5 is in this case a BLE peripheral server. The central device should only read one value at a certain time...
Hi:
I output a PWM channel in 16kHZ,i found that when i set the duty cycles 50%,my tft screen(i2c) display at a very slow speed,and it will be OK when i set duty cycles...
Hi,
I am trying to add a notification charactersitics on client, I am able to add one of them, but when i try to add another one sd_ble_gattc_write(), result is always NRF_ERROR_BUSY...
I am trying to use my nRF51 Dongle (pca10031) as a central.
I downloaded the nRF5_SDK_12.3.0_d7731ad and I could see that there is no BLE project for pca10031 (only pca10028...
i used nRF5_SDK_14.1.0_1dda907.
ANT protocol :
I used ant_background_scanning example.
I want to scannig device ID of hrm, bpwrt and bsc.
Then choose the device ID...
Looking forward to using the new sdk v15! Is there a plan to implement a new Bluetooth Developer studio plugin or should we go ahead and keep using the current version? We...
Hi, I encountered the following error in keil v5.12.0.0:
linking... .\_build\nrf51422_xxac.axf: Error: L6218E: Undefined symbol nrf_drv_gpiote_in_event_enable (referred...
Hi,
During SD+BL OTAU form SD132 ver 3.1.0 to SD112 ver 5.1.0, Old bootloader copied new one using function nrf_dfu_mbr_copy_bl(uint32_t * p_src, uint32_t len); to bad address...
Hi,
I have nrf52840 DK, I am unable to find details of which debug pin connected connected to respective controller pin.
basically dev kit has 10pin "Debug input" I want...
