We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
hi,
I an trying to enable notification from server. According to spec. i have to write 0x01 to the CCCD handle in heart rate characteristic in ble_app_hrs. In the BLE_GATTS_EVT_WRITE...
hi everyone
(1) everytime,the pstorage_init get the same block id, if we wrtie it more than 20,000 times , will this block become a bad one? if it will, can the program automatically...
Hi, Ole
I am using Nordic development board with Nordic dongle to communicate,..but I am getting receive link loss. I have removed reset from error handler, though the...
I have a setup where I will be switching the nRF51822 UART between two different peripherals (one being a connection to another nRF51822), so I need to be able to safely close...
Folks,
Sorry if I'm just being boneheaded here, but have been fighting with a couple problems while migrating my app on nRF51822/"C0"/SDK 4.2.2/S110 5 to nRF51822/"G0"...
We have made a custom board using nRF51822 connected to a MPU6050 accelerometer running on a battery.
Currently, we have issues performing reset on the chip. We have to...
Hi
I'm trying to measure the frequency of a pulse signal that runs at a moderate pace, varying between 50 and 500Hz while the SoftDevice is active. The softdevice needs...
Hi all,
I am having a bit of a problem with the printf. I could not figure out what could be the problem. From what I search people seem to be getting it working with out...
hi....
how can i implement bonding in app_ble_hrs example code from SDK V6.1.0 with soft device V7.0.0. the bonding should be done with a pass key.
can any one help...
Tried V5 a few months ago. But Nordic Semi didn't support their devices at that time.
I installed V5 today, and found a bunch of goodies :-), even including a nRF-RTX! ...
Hi
We did a few tests with the S120 softdevice (example in the SDK 5.1). Most things are working as expected, but the range of the device is by far less than we reached with...
I have been working on making at least 1us Timer interval(expect faster than 1MHz) using interrupt.
To do this we need to set the prescaler of Timer to 4, since formula...
Hello, sorry if this is a stupid question, but i'm fairly new to BLE (nRF51822), and even newer at report descriptors.
I'm using a nRF51822, SDK6.0.0 and S110 7.0.0.
In...
I saw softdevice no memory every several times, according to spec, softdevice use 8k, and app use 8k, are they share this 16k memory or no sharing, each use 8k, and reduce...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...