This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hey,
I am a bit confused with "client characteristic configuration" that is used to enable notifications (at least in Android).
To enable the notifications I have to...
The manual for my Agilent N4010A Wireless Test Set talks about a BER test based on a "vendor specific loopback test mode". This mode would allow me to do BER measurements...
Hi there,
I am starting with nrf52 and SDK 9.0.2 and am struggling with the SDK structure.
Can anyone please explain the difference between
components/libraries/uart...
Hello, I have tried to combine saadc with softdevice, but having errors during compiling. I have copied .c and .h files from saadc example to ble_hrs example, but having following...
Hi,
I have a specific application/product where in I am planning to use Nordic nRF52832.
-> There is a 9 Axis Inertial Measurement Unit (accel/gyro/magnetometer) connected...
Hi!
I have been trying for over a year to figure this out, but I am unable to, and I would hope it be pretty straight forward since OTA is already in the Nordit Master Control...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
I have a device (configured as a slave) which is connected to a relay to on/off a motor.
Now, I need to connect it to multiple masters (e.g., couple of smartphones) to remotely...
Hello Guys,
I need suggestion regarding the selection of nrf8001 ble module
Does it support OTA updates?
What is communication interface? is it SPI or conventional...
Hi,
I want to discovery all attribute UUIDs as Master Control panel application does. I use API function 'sd_ble_gattc_primary_services_discover' to discovery.
Exactly...
Hi:
I develop my project with gazell, Device can keep send to host,but host can't keep send to device(I'm not mean for host sent ack to device).
In my program, I use "nrf_gzll_add_packet_to_tx_fifo...
In the nRF52 reference design, not using the DC-DC converter would result in higher power consumption. By how much? Any documentation regarding the details. Thanks
Hi all,
I am new in nRF51822. Today I am doing experiment using GPIO and radio transmission.
I wrote a very simple code as below:
int main(void)
{
init_clock();...
Hi, I've got a serious problem in my project. Some of its features require hard timings. The usage time of these features is longer than the single timeslot and I must be...
Hello guys, I'm doing a hobby project and can't seem to get it working. Aim of the project is to transmit temperature values from a DS18B20 using an Arduino Uno and NRF24l01...
