Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
Can you please help us to convert following snippet from dts to mp_static.yml to use it for DFU applcation. We have external nand flash which used with littlefs and internal...
Hi all,
I have to measure the frequency of a PWM signal routed to one of the nRF52840 GPIO pins.
The signal frequency is ~3MHz.
The measurement is done with the help...
I am encountering the error message " <err> net_pkt: Uncontiguous data cannot be linearized " when already connected with nRF7002-DK to a Wi-Fi network using the EAP-TLS authentication...
I'm following the nordic academic courses, which are very nice by the way!
I've now followed three topics and I find three different variants which confuse me a lot: ...
Hi there,
So in my previous posts, I have been asking questions about setting i2s on two nRF devices in different modes. I have been successful in making it work.
...
Hello,
is it possible to read UICR at address FF8000 from a non secure application for nrf(160.
If yes, can you provide sample code and CONFIG to enable in prj.conf. ...
Hi,
I’m currently working with the nRF9151DK and using the nrf_modem_lib to test some AT commands. However, I’ve encountered an issue with the SIM.
When executing the...
When using the SPIM4 at 8 or 16 MHz, the clock looks nice and even. But at 32 MHz it consistently skips a half beat on the 16th clock pulse. In other words, while all the...
I am working on nRF54L15 and I want to store some user data in flash and for that I want to define the partitions.
I have selected the Target: nrf54l15dk/nrf54l15/cpuapp...
I am running smp_svr demo on my nrf54l15DK board, and use mcumgr command on my linux.
I could connect to my ble device and echo hello successfully (via peer_name='Zephyr...
Body:
Hello Nordic Team and Community,
I am working on a project using an nRF52840 chip on a custom breakout board . I am not using any pre-made development boards or...
During the testing phase of my device I use the Zephyr (uart) logging module and the Zephyr shell module(CONFIG_SHELL_LOG_BACKEND=y). Shell is mostly disabled, and is enabled...
I followed the migration guide for NCS 2.8.0 here for a custom board with engineering rev B silicon. After doing so I can't flash the board anymore and it gives me this error...
