I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
Hi,
In the API, the user gives the 'distance_us' parameter for the next requested slot. I have noticed that this is quite accurate (to the micro) and wanted to know if...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
Hi All.
I made my PCB with nRF51822 and achieved around 150 Feet range (LoS). My target is to calculate a approximate distance (in Feet) from RSSI values.
I did a field...
I want to set up the HRS demo, but in reverse. I want to use my PCA10001 board to receive heart rate data from a peripheral device (already working and tested on my PC). It...
Hi,
i have a problem in my Code, when ic look nrf_delay_us (1000) on the oscilloscope i can se a puls withe 1,3 us thats not accurate enough. What could be a reason for...
Hi,
I have created Eclipse project to compile nRF51 DFU loader. This is a pure Eclipse project, no makfile. It has compile configurations for combination of Single/Dual...
Hi,
I am looking to build a beaon product based on nRF51822. There are several kits available shown below. Which kit should I pick to start the hardware design and firmware...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hello,
I am using nrf51822 evaluation kit with ble_lbs (Led button sample) profile, I need the USB dongle source code for ble_lbs (Led button sample) profile because I...
Hi,
Is it possible to change the advertisement parameters of a beacon device without connecting to it?
(ex: major,minor value & interval)
Is it OK if our beacon product...
I use ble_app_uart demo of pca1001 and my SDK version is 5.2.0. I want to use APP_BUTTON_INIT to handle a button event. So I changed the buttons_init(void) like this:
static...
Hi, is it possible to add for example a
www.ti.com/.../technicaldocuments
On the nrf51822?
I would have to modify the S110 source to turn on and off the LNA and PA when...
Hi
I have created local buffer of 100 bytes.
while device is connected to dongle it is sending all 100 bytes over bluetooth stack .
but once it is disconnected and...
Hi everyone, I don't have the nRF51822 yet, but still want to get familiar with it as much as possible before I get to buy it. I was looking for a description of the functions...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
