Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Designing a custom pcb, we have a few questions, and maybe you could help a little bit.
On this Nordic design ,before proceeding to layouts :
Can I skip pins 45/46...
So im trying to create a generic library to test any Bluetooth device. So far i can connect to the device but since i dont know what are the services and UUID available im...
Tried Flasher Portable Stand-Alone Mode with J-Flash 6.14 as following:
Create .jflash Project for nRF51822-QFAA
Open Data .Hex File
From J-Flash, select Target...
Hi,
This is obviously not the first question about this, but I still haven't found the answer I need here...
I would like to make a kind of serial to BLE gateway on...
Hello Nordic Community.
I'm having issues trying to control a simple RGB LED circuit with the NRF52. I have set up 2 timers and PWM instances Red and Green on PWM1 and...
I am performing automated testing on my device using an xml file that I have written. My xml contains a disconnect command. I observed that NRF connect reconnects to my device...
Hello,
After looking for pin mapping for TRACECLK and TRACEDATA[*] for nrf52840 I've seen 3 different mappings:
P0.07, P1.00, P0.11, P0.12, P1.09 in infocenter.nordicsemi...
Hi
I need to send as much data as it is possible in the advertisrment payload. Whem weset the devicename there are other fields that are automatically added to the payload...
I'm having issues executing any Zephyr project on a breadboard connected to a ISP1302. It works fine on the nRF51-DK but anything I try a final hardware nothing happens. Tried...
Hello,
I am using nrf52832 with PCA10036 V1.1.0. Soft device code is s132. I would like to know whether it will support Bluetooth 5.
I have downloaded nrf52 sdk13.0...
Hi, Dear Expert:
I am an Electronic Engineer. We used nRF51422 or nRF51822 at our products, but found the products was easily reset when did +/-1KV contact ESD testing...
now I used sample code of radio
change NRF_RADIO->MODE = (RADIO_MODE_MODE_Nrf_2Mbit << RADIO_MODE_MODE_Pos)；
In transmitter code , I change
while (true...
Story Short: When trying to run the ble_app_uart example on a custom board with a nRF51822QFAAH0 chip, the code faults and resets at the point in tries to call sd_softdevice_enable...
I would appreciate some suggestions on a good development flow to go from an Example to end application
I have nrf52832 on a custom PCB.
I tested several sdk13.0.0 examples...
