But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
I am using a nrf51822 based tag and Android official SDK to implement my custom app. I perform the following steps:
1. Scan
2. Connect
3. Discover services
4. Write...
What CRC type is used for the crc calculation with the function
uint16_t crc16_compute (const uint8_t * p_data, uint32_t size, const uint16_t * p_crc )
of the nRf52 SDK...
Hi
I have a prototype of a board that uses a nNF52832 to communicate over Bluetooth, the board has some buttons intended for user input.
As the board size is little...
Hello!
I am sorry to ask a simple question that why my device can't program the ".hex" file about the demo of ble_app_hrs_rscs_relay_s130_pca10028 after I have already program...
Hi,
I have Wifi MCU connected to nr51822.
I download the binary file from a Cloud and need to transfer it via UART, so i need a C code of the nRF5x Programing tool....
Hi,
I am not able to make software breakpoints working with a Segger J-Link probe.
As an exemple, here is my assert callback function:
void __attribute__((noreturn...
Hi.
I'm using nRF51822QFAC, SDK10.0.0, S130.
I want to use DTM code to get SIG certification.
In your example, there is no source code for S130 but S110, S120, S310....
My BLE application needs to occasionally (1-2 times a year) send large amounts (several kbytes) of data, and I'm wondering about how to make this happen as fast as possible...
I am just wondering if anyone else has seen this issue.
I am working on the ble_app_uart_s132_pca10040 on the nRF52 DK.
Using the Android UART v 2.0 app I can connect...
Hi:
A peculiar problem:
I configured an Arduino (atmega328P) to be a receiver and an atmega8A to be a Transmitter Things are fine. The Arduino receives a 10 byte string...
We are developing a beacon device with 10dBm power amplifier. During software development we noticed the control signals provided by ble_common_opt_pa_lna_t align poorly with...
Hi,
As title ,
I try to add the NUS service that show on the ble_app_uart project into Multi-link project.
But it doesn't work .
I want to a central connected to at...
I want to use PWM on only one output pin. I'm using a nrf51422 and softdevice s130.
I want to be able to set the PWM and then change it again (a sequence). This is to be...
I have tried using the pre-built nRFUart Example in the Master Emulator API (2.1.11.1) and get the above error
I also tried rebuilding - no change.
I do have a PCA10000...
