Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hello:
I am use nrf51822 to transfor data (BLE <->UART),i need a faster rate in ble , and i found a way in the zone,that to use BLE_EVT_TX_COMPLETE to send data, the send...
I would like to use the A/D converter to monitor the battery voltage and need to know if the 0.6V reference is generated with a bandgap or some sort of divider network.
...
Hi,
Next problem I've experienced is jumping processor to Hardfault state at sd_ble_gap_adv_start
with whitelist and BLE_GAP_ADV_FP_FILTER_CONNREQ .
In case adv_params...
Hi
Although I followed and got working eclipse Mars on win10 using this great @Vidar tutorial I am still having problem creating a new project under eclipse for any of...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I am developing a power aware TWI driver for 51822/422. All appears to work properly except when I simulate a bus fault by shorting SCL to ground or shorting SCL and SDA together...
Hi,
Firstly a warning I'm a noob in this area.
I'm seeing some strange events consistently returned from the nRF8001 over SPI. I have an example of the SPI traffic below...
Hi! I would like to get adc sample from two different channels at the same time on my beacon (nrf1822), using the same interrupt. Is that possible?I mean I can use ADC_IRQhandler...
Hi,
It's a very simple question, is there a simple way to check GPIO pin status. I just want to know at a given time if the Pin is High/Low. I don't think I need an ISR...
Hi, I just started working on nRF52 with Bluetooth, and I have some concerns about DFU and security.
I’m working on a product equipped with an nRF52 and a MEMS microphone...
Hi!
I am using the NUS service and I noticed that Android 6 (Marshmallow) will not go faster that 47.5 ms. Even iOS can go to 30ms. My target is 7.5.
Am I doing something...
Hello,
I am using nRF52832 with S132 and SDK_11.0.0. I am facing issue with using power fail warning POFWARN. below is my code snap.
void POWER_CLOCK_IRQHandler(void...
Hi All.
I'd like to know how to turn off or on shockburst feature.
After I set auto ack & retry count, Tx successful interrupt occurs, even though receiver device is in...
I'm migrating an app from SDK8 to SDK11 and I'm getting errors using TWI to communicate with my IMU (Invensense 9250). I first tried it on a nRF52 DK (Eng B) and then went...
