I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
As far as I understand I should be able to use the nrfutil (6.1.x) on a Rpi 4B to update any of the nordic semi devices nrf5x supporting bluetooth (i my case nrf5340) Will...
I am new on Bluetooth. Currently I am playing with BL5340 development board. I need a firmware to test Bluetooth data transmission latency between two BL5340 modules. Could...
Hello,
I'm running the Asset Tracker V2 NCS 1.7.0 conected to the nRF Cloud. I'm using a Thingy:91 with external GPS antenna.
The GPS position is being correctly aquired...
Hello ,I am starting new development in Nordic environment and my system configuration is intel i3 with 8gb ram.
Still it is way too much slow to open nrf connect for desktop...
Hello everyone,
i want to use the 52810 to write into a SD -card, i use a slightly modified fatfs example.
The problem is, the SD card will not initialize as the p_event...
Hi, I'm trying to implement a sleep mechanism in my app. I based my code on the Power Management Example.
I use a button to put the app to sleep and the same button to wake...
Hi Team,
I am working on a project. It requires nordic chips (slaves) to communicate with msp430 (master). I use the nordic example SPIS as the initial code of the nordic...
My project consists of STM32 + 4G + nrf52833. When the 52833 firmware needs to be updated, the cloud service will send the 52833 firmware to STM32, and then STM32 will send...
Hello all!
I am currently developing on the development board nRF52832, SDK16.0 and SD132v7.2.0.
My developmnet board acts as a central whereas my phone as peripheral...
Dear team,
1. I am using the Ble_app_uart example from the SDK.
2. I had received the data successfully from the nrf_connect app.
3. Once the data was received over...
I received my nRF52840-DK (PCA10056) last week and today I was given the task to get started.
I started setup my environment with my preferred choice: Arduino IDE. Unfortunately...
Hi
In the actual test, the power consumption of the chip when scanning is started is 9.5mA,This actual test value is higher than the Iradio_rx0 and Is1 in the PS .What is...
Hi
The customer wants to test the RF transmit power of the nrf9160，whether the AT command can be fixed frequency?Or whether there are special tools to test RF power?
Hi,
I'm trying to migrate bluetooth softdevice to a project contained cli module. I found cli module and softdevice would all create an app timer. The softdevice first created...
Hi,
i using 52840DK 10056, keil5
SDKs\nRF5_SDK_17.0.2_d674dde\examples\ble_central_and_peripheral\experimental\ble_app_multirole_lesc\
i got err or as follows ,but the...
